Проблем с Xtrend 9000

[cecopeco]

ВИЖ това http://dtv-bg.com/showthread.php?t=29215 и http://dtv-bg.com/showthread.php?t=22652&page=3

и кажи дали проблема е същия

Първия линк не отговаря на моя проблем, а по скоро вторият, проблема е можеби в буутлоудера но не мога да намеря по нов от 2012г Някакви решения?

[tibuzdrev]

Първия линк не отговаря на моя проблем, а по скоро вторият, проблема е можеби в буутлоудера но не мога да намеря по нов от 2012г Някакви решения?

 това е бутлоудера,пробвай да го префлашнеш но не вярвам да се оправи

[cecopeco]

това е бутлоудера,пробвай да го префлашнеш но не вярвам да се оправи

Направо ме окуражи, а аз щях да черпя бира!

[tibuzdrev]

може да пробваш и това от няколко дена е

Хtrend Reparatur mit SecureCRT     Mit einem Terminal Programm wie Secure CRT kann man manche Fehler selber beheben.
Wenn z.B. das Mainboard defekt ist, kann man ein anderes Mainboard (Bei dem z.B. das Secboard defekt ist) einbauen. man muss nur dem neuen mainboard die mac Adresse des defekten verpassen, schon läuft das Secboard mit dem neuen Mainboard.

Auch ein Fehler beim Flashen des Bootloaders kann so behoben werden.

Hier die Befehle:

1. Bootloader flash:


The image files must be placed on the root of USB stick.
After inserting the USB stick to your Xtrend and turning it on, click CTRL + C numerous times on Secure CRT,
then enter these commands:

flash –noheader usbdisk0:cfe.bin flash0.cfe

flash –noheader usbdisk0:splash.bin flash0.splash

reboot

1.1 Image flash:

flash –forceerase –noheader usbdisk0:kernel.bin nandflash0.kernel

flash –forceerase –noheader usbdisk0:rootfs.bin nandflash0.rootfs

reboot

CFE>unsetenv STARTUP

If it don't have mac address label, you have to read that in the CFE> mode. than you save that to the different location


CFE> ^C // click " Ctrl+C " as soon as it turn on STB

CFE> ^C


CFE> printenv // Display the environment variables


Variable Name Value
-------------------- --------------------------------------------------
BOOT_CONSOLE uart0
LINUX_FFS_STARTAD 0
LINUX_FFS_SIZE 0
SPLASH_PART_STARTAD 80000
SPLASH_PART_SIZE 200000
STARTUPVERSION 1
ETH0_HWADDR XX:XX:XX:XX:XX:XX // you can see the MAC Address here
LINUX_PART_STARTAD 0
LINUX_PART_SIZE 600000
DRAM0_SIZE 512
DRAM1_SIZE 0
FLASH_TYPE NOR
FLASH_SIZE 4
CFE_VERSION 2.12.26
CFE_BOARDNAME BCM97405B1
CFE_MEMORYSIZE 128

*** command status = 0


CFE>


2. replace IC (nor , nand flash )

Turn off STB and than replace IC (nor , nand flash ) on the STB pcb.
Take notice you don't miss each nor flash (3 type:ET5X00,ET6X00,ET9X00)


3. Writing MAC Address

Write MAC Address in the nor flash after you go to CFE> mode.

CFE> help macprog2 // you can see function, use form of the macprog2 command

SUMMARY
Program a specific MAC address.

USAGE
macprog2

This command programs board specific MAC addresses to the
flash. (ex. macprog2 00-01-FE-40-09-F2) // use form

*** command status = 0

CFE>

CFE> macprog2 00-01-FE-40-09-F2 // write MAC Address in the STB

Programming flash...done

*** command status = 0

Angaben ohne Gewähr, bitte nur bei bereits defekten Geräten ausprobieren!!!
http://www.et-view-support.com/Forum/showthread.php?13957-Xtrend-Reparatur-mit-SecureCRT

[cecopeco]

може да пробваш и това от няколко дена е

Хtrend Reparatur mit SecureCRT     Mit einem Terminal Programm wie Secure CRT kann man manche Fehler selber beheben.
Wenn z.B. das Mainboard defekt ist, kann man ein anderes Mainboard (Bei dem z.B. das Secboard defekt ist) einbauen. man muss nur dem neuen mainboard die mac Adresse des defekten verpassen, schon läuft das Secboard mit dem neuen Mainboard.

Auch ein Fehler beim Flashen des Bootloaders kann so behoben werden.

Hier die Befehle:

1. Bootloader flash:


The image files must be placed on the root of USB stick.
After inserting the USB stick to your Xtrend and turning it on, click CTRL + C numerous times on Secure CRT,
then enter these commands:

flash –noheader usbdisk0:cfe.bin flash0.cfe

flash –noheader usbdisk0:splash.bin flash0.splash

reboot

1.1 Image flash:

flash –forceerase –noheader usbdisk0:kernel.bin nandflash0.kernel

flash –forceerase –noheader usbdisk0:rootfs.bin nandflash0.rootfs

reboot

CFE>unsetenv STARTUP

If it don't have mac address label, you have to read that in the CFE> mode. than you save that to the different location


CFE> ^C // click " Ctrl+C " as soon as it turn on STB

CFE> ^C


CFE> printenv // Display the environment variables


Variable Name Value
-------------------- --------------------------------------------------
BOOT_CONSOLE uart0
LINUX_FFS_STARTAD 0
LINUX_FFS_SIZE 0
SPLASH_PART_STARTAD 80000
SPLASH_PART_SIZE 200000
STARTUPVERSION 1
ETH0_HWADDR XX:XX:XX:XX:XX:XX // you can see the MAC Address here
LINUX_PART_STARTAD 0
LINUX_PART_SIZE 600000
DRAM0_SIZE 512
DRAM1_SIZE 0
FLASH_TYPE NOR
FLASH_SIZE 4
CFE_VERSION 2.12.26
CFE_BOARDNAME BCM97405B1
CFE_MEMORYSIZE 128

*** command status = 0


CFE>


2. replace IC (nor , nand flash )

Turn off STB and than replace IC (nor , nand flash ) on the STB pcb.
Take notice you don't miss each nor flash (3 type:ET5X00,ET6X00,ET9X00)


3. Writing MAC Address

Write MAC Address in the nor flash after you go to CFE> mode.

CFE> help macprog2 // you can see function, use form of the macprog2 command

SUMMARY
Program a specific MAC address.

USAGE
macprog2

This command programs board specific MAC addresses to the
flash. (ex. macprog2 00-01-FE-40-09-F2) // use form

*** command status = 0

CFE>

CFE> macprog2 00-01-FE-40-09-F2 // write MAC Address in the STB

Programming flash...done

*** command status = 0

Angaben ohne Gewähr, bitte nur bei bereits defekten Geräten ausprobieren!!!
http://www.et-view-support.com/Forum/showthread.php?13957-Xtrend-Reparatur-mit-SecureCRT

Май ще ходи при Продуцента на ремонт!

[cecopeco]

Бедна ти е информацията,ти ли го уби,или друг?

Е, мисля, че аз съм го убил! Ако ще помагаш - помагай.