The Best Streaming Software! VIVO Rent A Car - Your car rental
 

Чат

🕑 ↗
За да пишеш, трябва да си влязъл в профила си.

Настройки на Mgcamd

Започната от ko2000, 27-04-2011, 21:57

« назад - напред »

0 Потребители и 2 гости преглеждат тази тема.

Формат за разпечатване
Надолу Страници 1 2 3 4 5 ... 8
Действия

tok82

#30
23-10-2011, 14:22
Цитат на: манира;125425Здравейте .

Да питам , ако е възможно .

Вече няколко месеца тествам " заргакум " .
Да ви питам относно " SKY ITALY " , " SKY UK " !
Пробвал съм само " SKY ITALY " . При вас как е , има ли НАКЪСВАНИЯ ?
Тези от вас които са тесвали " SKY UK " , биха ли казали как е при тях , насича ли ?

Предполагам голяма част от вас се сещат какво по-точно имам във предвит .
А ето и как стоят нещата при мен .
Скоростта на нета е добра и интернет-доставчика е добър , интернетският кабел директно е забоден в DREAMBOX-а ,
и не минава през рутер ( имам във предвит ,че в къщи не минава през рутер ) !
Ползвам настройките изпратени от оператора " заргакум " .

Въпросът ми е : Има ли универсални настройки на  ( replace.list , priority.list ,ignore.list ) за нашите ширини ,
които биха подобрили , или изцяло премахнали накъсванията .

Благодаря предварително на всички които биха помогнали .
Моля модератоите ако сметнат темата за неуместна да я премахнат !

къвто да е интернета ти каквото и да направиш сървара им сече яко навсякаде е така
extrend et4000;5xdm500s;1xdb500-c;cryptobox 500hd;1x ariva 102e;1 x goldenmedia black;3,60m,1,50m,2x1m antena linear motor superjack18;mag250

jycom

#31
03-11-2011, 19:19
с това ли се раздават линии?
 
# sample peer.cfg for gbox client in mgcamd
# syntax the same as in cwshare.cfg,
# you can just copy cwshare.cfg to this file.
# see below for supported tags, others not supported (yet).
# max cards to send ecm too + preffered cards ids (up to 32)
X: { 05 } 1234 ABCD
# max card's distance to use for ecm
I: ( 05 }
# resend after 2 seconds, re-sync (send to all) after 3 seconds
N: { 0 0 0 0 2000 3000 }
# same, but for NDS cards
S: { 0 0 0 0 400 500 }
# my host and password
M: { my.dyndns.com { 1234ABCD }}
# peers, unlimited number, but only up to 32 unique ports to listen
# host, port to listen, remote port, password, levels (ignored)
D: { peer1.dyndns.com { 2471 3471 { ABCD1234 { 9 9 }}}}
D: { peer2.dyndns.com { 2471 3471 { 6789ABCD { 9 9 }}}}
# ignore ids
Y: { 01 02 }
Y: { 02 03 }
# always save ids, caid-id + id
G: { 05023B00 1234 }
G: { 01000065 5678 }
# virtual cards
V: { 01 { 05 00 7C 00 }}
V: { 02 { 18 01 04 01 }}
V: { 02 { 18 01 05 01 }}
V: { 03 { 18 01 40 01 }}
V: { 03 { 18 01 41 01 }}
 
 
и възможно ли е?

bu12tras

#32
03-11-2011, 19:55
Не Mgcamd е само клиент не може да "раздаваш" линии от него.

lacosa

#33
08-11-2011, 23:21
Koлеги да не отварям и аз нова тема,къде ми грешката?


tuxbox mgcamd v1.35a by mixvt (compiled Jan 26 2010 15:59:20)
[mg] ▒Net:1:1:0:3s Show ecm:1, emm:0 Up:1 Au:0 Dir:0 Osd:no:80:0 Cache:0 ▒Log:4:192.168.1.1:514 Reread:0
[mg] Ecm cache time: 7
Box type: ▒mips dreambox (dm7025, dm800)
Conax.Key error 2: No such file or ▒directory
SoftCam.Key error 2: No such file or ▒directory
AutoRoll.Key error 2: No such file or directory
Conax.Key ▒error 2: No such file or directory
ignore prov 0100:000076
ignore ▒prov 0100:000070
ignore prov 0100:000084
ignore prov ▒0100:000085
ignore prov 0100:000089
ignore prov ▒0500:020000
ignore prov 0500:000000
ignore prov ▒0500:008300
ignore prov 0500:008100
ignore prov ▒0500:008110
ignore prov 0500:022600
ignore prov ▒0500:008000
ignore prov 0500:00C400
ignore caid 0960
ignore ▒caid 0918
ignore caid 1810
ignore caid 4AD4
ignore caid ▒0D05
ignore prov 0600:000026
ignore prov 0600:000032
ignore ▒prov 0600:00003A
ignore prov 0600:00003C
ignore prov ▒0600:0000AB
ignore prov 0600:0000AC
ignore prov ▒0600:000092
ignore prov 0600:0000AD
ignore prov ▒0600:000037
priority prov 0500:015000
priority prov ▒0100:000080
priority caid 0602
priority caid 1722
ecm replace ▒000A:0500:042700:0026 -> 0000:000000:0000
ecm replace ▒0014:0500:042700:0027 -> 0000:000000:0000
ecm replace ▒001E:0500:042700:0028 -> 0000:000000:0000
ecm replace ▒3717:0500:023700:0FA3 -> 0500:030600:0BBB
ecm replace ▒3716:0500:023700:0FA2 -> 0500:030600:0BBA
ecm replace ▒3715:0500:023700:0FA1 -> 0500:030600:0BB9
ecm replace ▒2F4A:0500:023700:0FA6 -> 0500:030600:0BBE
ecm replace ▒2F45:0500:023700:0FA1 -> 0500:030600:0BB9
ecm replace ▒2F46:0500:023700:0FA2 -> 0500:030600:0BBA
ecm replace ▒2F47:0500:023700:0FA3 -> 0500:030600:0BBB
ecm replace ▒3718:0500:030600:0BBC -> 0000:000000:0000
ecm replace ▒3719:0500:030600:0BBD -> 0000:000000:0000
ecm replace ▒371A:0500:030600:0BBE -> 0000:000000:0000
ecm replace ▒2F48:0500:023700:0FA4 -> 0500:030600:0BBC
ecm replace ▒2F49:0500:023700:0FA5 -> 0500:030600:0BBD
ecm replace ▒000A:4AE1:000000:0078 -> 0000:000000:0000
ecm replace ▒0050:4AE1:000000:0078 -> 0000:000000:0000
ecm replace ▒0028:4AE1:000000:0027 -> 0000:000000:0000
ecm replace ▒0032:4AE1:000000:0027 -> 0000:000000:0000
ecm replace ▒0046:4AE1:000000:0078 -> 0000:000000:0000
ecm replace ▒0014:4AE1:000000:0030 -> 0000:000000:0000
ecm replace ▒001E:4AE1:000000:006E -> 0000:000000:0000
ecm replace ▒006E:4AE1:000000:0032 -> 0000:000000:0000
ecm replace ▒005A:4AE1:000000:0078 -> 0000:000000:0000
ecm replace ▒0064:4AE1:000000:0078 -> 0000:000000:0000
ecm replace ▒003C:4AE1:000000:0026 -> 0000:000000:0000
ecm replace ▒0078:4AE1:000000:0026 -> 0000:000000:0000
ecm replace ▒1D64:4AE1:000000:0020 -> 0000:000000:0000
ecm replace ▒1D4E:4AE1:000000:0020 -> 0000:000000:0000
ecm replace ▒1D4F:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒1D53:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒1D55:4AE1:000000:0020 -> 0000:000000:0000
ecm replace ▒1D59:4AE1:000000:0020 -> 0000:000000:0000
ecm replace ▒1D54:4AE1:000000:0020 -> 0000:000000:0000
ecm replace ▒1D56:4AE1:000000:0020 -> 0000:000000:0000
ecm replace ▒1D51:4AE1:000000:0020 -> 0000:000000:0000
ecm replace ▒1D57:4AE1:000000:0027 -> 0000:000000:0000
ecm replace ▒1D5C:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒1D5A:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒1D5B:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒1D5E:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒1D52:4AE1:000000:0020 -> 0000:000000:0000
ecm replace ▒1D60:4AE1:000000:0027 -> 0000:000000:0000
ecm replace ▒1D5D:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒1D58:4AE1:000000:0027 -> 0000:000000:0000
ecm replace ▒1D5F:4AE1:000000:0027 -> 0000:000000:0000
ecm replace ▒1D50:4AE1:000000:0020 -> 0000:000000:0000
ecm replace ▒012D:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒012E:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒012F:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0130:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0131:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0132:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0133:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0134:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0135:4AE1:000000:0029 -> 0000:000000:0000
ecm replace ▒0136:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0137:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0138:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0139:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒013A:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒013B:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒013E:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒013F:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0140:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0141:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0142:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0143:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0144:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0145:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0146:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0147:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒0148:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒014A:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒014B:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒014C:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒014E:4AE1:000000:0041 -> 0000:000000:0000
ecm replace ▒014F:4AE1:000000:0043 -> 0000:000000:0000
ecm replace ▒0150:4AE1:000000:0045 -> 0000:000000:0000
ecm replace ▒0151:4AE1:000000:0047 -> 0000:000000:0000
ecm replace ▒019A:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒0003:2600:000000:1FFF -> 0000:000000:0000
ecm replace ▒0385:4AE1:000000:0026 -> 0000:000000:0000
ecm replace ▒0386:4AE1:000000:0026 -> 0000:000000:0000
ecm replace ▒0387:4AE1:000000:0026 -> 0000:000000:0000
ecm replace ▒0388:4AE1:000000:0026 -> 0000:000000:0000
ecm replace ▒0389:4AE1:000000:0026 -> 0000:000000:0000
ecm replace ▒038A:4AE1:000000:0026 -> 0000:000000:0000
ecm replace ▒038B:4AE1:000000:004F -> 0000:000000:0000
ecm replace ▒038C:4AE1:000000:004F -> 0000:000000:0000
ecm replace ▒038D:4AE1:000000:0053 -> 0000:000000:0000
ecm replace ▒003B:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒61A8:4AE1:000000:0029 -> 0000:000000:0000
ecm replace ▒61B2:4AE1:000000:0029 -> 0000:000000:0000
ecm replace ▒61BC:4AE1:000000:0029 -> 0000:000000:0000
ecm replace ▒61C6:4AE1:000000:0029 -> 0000:000000:0000
ecm replace ▒61D0:4AE1:000000:0029 -> 0000:000000:0000
ecm replace ▒61DA:4AE1:000000:0029 -> 0000:000000:0000
ecm replace ▒61E4:4AE1:000000:0029 -> 0000:000000:0000
ecm replace ▒61EE:4AE1:000000:0029 -> 0000:000000:0000
ecm replace ▒61F8:4AE1:000000:0029 -> 0000:000000:0000
ecm replace ▒6202:4AE1:000000:0029 -> 0000:000000:0000
ecm replace ▒620C:4AE1:000000:002A -> 0000:000000:0000
ecm replace ▒6216:4AE1:000000:002A -> 0000:000000:0000
ecm replace ▒6915:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒6916:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒6917:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒6918:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒6919:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒691A:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒691B:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒691C:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒691D:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒691E:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒691F:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒6920:4AE1:000000:0023 -> 0000:000000:0000
ecm replace ▒697D:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒6982:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒6987:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒698C:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒6991:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒6996:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒69A0:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒69AA:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒69B4:4AE1:000000:0029 -> 0000:000000:0000
ecm replace ▒69D2:4AE1:000000:0028 -> 0000:000000:0000
ecm replace ▒69DC:4AE1:000000:0029 -> 0000:000000:0000
ecm replace ▒69E6:4AE1:000000:0029 -> 0000:000000:0000
ecm replace ▒69F0:4AE1:000000:003D -> 0000:000000:0000
ecm replace ▒7922:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒792C:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒7936:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒7940:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒794A:4AE1:000000:002B -> 0000:000000:0000
ecm replace ▒7954:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒795E:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒7968:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒7972:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒0A29:4AE1:000000:0027 -> 0000:000000:0000
ecm replace ▒0A2A:4AE1:000000:006E -> 0000:000000:0000
ecm replace ▒0A2B:4AE1:000000:0027 -> 0000:000000:0000
ecm replace ▒0A2C:4AE1:000000:0027 -> 0000:000000:0000
ecm replace ▒0A2D:4AE1:000000:0027 -> 0000:000000:0000
ecm replace ▒0A33:4AE1:000000:0027 -> 0000:000000:0000
ecm replace ▒0A34:4AE1:000000:006D -> 0000:000000:0000
ecm replace ▒0A35:4AE1:000000:0027 -> 0000:000000:0000
ecm replace ▒0A36:4AE1:000000:0073 -> 0000:000000:0000
ecm replace ▒0A38:4AE1:000000:0027 -> 0000:000000:0000
ecm replace ▒0D49:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒0D4A:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒0D4B:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒0D4C:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒0D4D:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒0D4E:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒0D4F:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒0D50:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒0D51:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒0D52:4AE1:000000:002C -> 0000:000000:0000
ecm replace ▒0D54:4AE1:000000:002C -> 0000:000000:0000
[config] newcamd route = ▒xxxxxx:178.162.167.xxx:3031
newcamd keep alive: 600, incoming port: ▒0
[mgcam] emm thread started
[newcamd] Connecting to ▒178.162.167.xxx:3031...
[newcamd] Login to 178.162.167.xxx:3031 as ▒xxxxxx accepted (109ms)
[newcamd] Card data from 178.162.167.xxx:3031 ▒(205ms):
Userid 189 caid 604 providers 1
Idents: ▒000000

got 51 cmd 9F
[mg0] namespace 18630EC t-id 1 on-id ▒1
[mg0] descramble on 1, source 0
[mg0] service 3EA index 0 pmt pid ▒169 (1), pids: video 0x0150, audio 0x0151
[mg0] ECM: CaID: 0x0604 ▒-> CaPID: 0x0CEA ProvID: 000000
[mg0] ECM: CaID: 0x5581 -> ▒CaPID: 0x0D4E ProvID: 000000
[mg0] No irdeto2 key(s) found for id 604 ▒keynr 04
[mg0] -> ECM to newcamd 178.162.167.xxx:3031
[mg0] ▒network can't decode
[mg0] No irdeto2 key(s) found for id 604 ▒keynr 04
[mg0] -> ECM to newcamd 178.162.167.xxx:3031
[mg0] ▒network can't decode
[mg0] pid 0x0CEA failed to decode.
[mg0] ▒network can't decode
[mg0] pid 0x0D4E failed to decode.
[mg0] ▒-> ECM to newcamd 178.162.167.xxx:3031
[mg0] -> ECM to newcamd ▒178.162.167.xxx:3031
[mg0] newcamd route 178.162.167.xxx:3031 cant ▒decode (4274ms)
[mg0] -> ECM to newcamd ▒178.162.167.xxx:3031
[mg0] -> ECM to newcamd ▒178.162.167.xxx:3031
[mg0] -> ECM to newcamd ▒178.162.167.xxx:3031
[mg0] -> ECM to newcamd 178.162.167.xxx

lacosa

#34
09-11-2011, 15:45
Никой ли няма да помогне? ;;601 :hammer:

spaice

#35
09-11-2011, 15:50
Цитат на: lacosa;128142Никой ли няма да помогне? ;;601 :hammer:
Нямаш файл SoftCam.Key за едната кодировка, а за другата от там не идва нищо.

lacosa

#36
09-11-2011, 16:28
то това не е с кодировка ,а узер и пасс

за да бъдe по точно ето друг лог


Mgcamd v1.37 by mixvt, patched by D2MAC on Sep 10 2011
[mg] Net:1:7:2:2s Show ecm:1, emm:0 Up:0 Au:0 Dir:0 Osd:no:80:0 Cache:7 Log:2:19
2.168.10.168:514 Reread:0
[mg] Ecm cache time: 36000
Box type: mips dreambox (dm7025, dm800)
root@et9000:~# [config] newcamd route = user:178.162.167.xxx:xxxx
newcamd keep alive: 600, incoming port: 12000
[mgcam] emm thread started
[newcamd] Connecting to 178.162.167.ххх:хх31...
[newcamd] Login to 178.162.167.ххх:хххх as 9nf0wie4 accepted (113ms)
[newcamd] Card data from 178.162.167.ххх:хххх (214ms):
        Userid 7 caid 604 providers 1
        Idents: 000000

got 50 cmd 9F
[mg0] namespace 1863167 t-id 5 on-id 1
[mg0] descramble on 1, source 0
[mg0] service CB index 0 pmt pid 200 (1), pids: video 0x0201, audio  0x01FF 0x02
02
[mg0] ECM: CaID: 0x5581  -> CaPID: 0x0F0D ProvID: 000000
[mg0] network can't decode
[mg0] pid 0x0F0D failed to decode.
root@et9000:~# killall  mgcamd_1.37
[mgcamd] signal 15 received
stopping mg0
[mg0] stoping camd..

ReVo

#37
10-11-2011, 09:32
Цитат на: lacosa;128149то това не е с кодировка ,а узер и пасс

за да бъдe по точно ето друг лог


Mgcamd v1.37 by mixvt, patched by D2MAC on Sep 10 2011
[mg] Net:1:7:2:2s Show ecm:1, emm:0 Up:0 Au:0 Dir:0 Osd:no:80:0 Cache:7 Log:2:19
2.168.10.168:514 Reread:0
[mg] Ecm cache time: 36000
Box type: mips dreambox (dm7025, dm800)
root@et9000:~# [config] newcamd route = user:178.162.167.xxx:xxxx
newcamd keep alive: 600, incoming port: 12000
[mgcam] emm thread started
[newcamd] Connecting to 178.162.167.ххх:хх31...
[newcamd] Login to 178.162.167.ххх:хххх as 9nf0wie4 accepted (113ms)
[newcamd] Card data from 178.162.167.ххх:хххх (214ms):
        Userid 7 caid 604 providers 1
        Idents: 000000

got 50 cmd 9F
[mg0] namespace 1863167 t-id 5 on-id 1
[mg0] descramble on 1, source 0
[mg0] service CB index 0 pmt pid 200 (1), pids: video 0x0201, audio  0x01FF 0x02
02
[mg0] ECM: CaID: 0x5581  -> CaPID: 0x0F0D ProvID: 000000
[mg0] network can't decode
[mg0] pid 0x0F0D failed to decode.
root@et9000:~# killall  mgcamd_1.37
[mgcamd] signal 15 received
stopping mg0
[mg0] stoping camd..

То си пише, че HobbyTV HD не може да се декордира. От руснаците можеш да гледаш само 0604, демек ирдето. Не ползвай техните replace, prio и ignore файлове. Пълни са с грешки, а и си ги правят за техните програми.
IPBOX 9000 HD, IPBOX 910 HD, IPBOX 200S, 2x DM500S, 2x 90 cm + 2x motor, 120 cm + motor, 80 cm - 75E

lacosa

#38
10-11-2011, 10:55
Благодаря за отговора.То си пише ама аз като не го виждам?  :hammer:

BOBIKAT

#39
15-12-2011, 23:10 Последна редакция: 15-12-2011, 23:12 by BOBIKAT
Да не отварям нова тема, но нещо се бъгна мгкам-а. А може и да е от салатата, незнам. В нюцс-а е сложена конакс картата, разпознава я:
[ 21:43:49 ] [ Loader ] Card 0B01 on port /dev/sci0 ready
[ 21:43:49 ] [ Loader ] Starting Newcamd Server on port 34000
[ 21:43:49 ] [ NewCS ] Ready to GO! :)
[ 21:43:49 ] [ Newcamd ] Newcamd thread Server started on port 34000
newcamd: main loop
root@dm800:~# [ 21:43:49 ] [ Newcamd ] recv: error! 146: Connection refused
[ 21:43:49 ] [ Newcamd:34000 ] User dummy logout
[ 21:44:04 ] [ Newcamd:34000 ] User dummy logged in, client: Mgcamd
[ 21:44:09 ] [ Newcamd ] ECM -> dummy (NOT OK) [CAID 0B01] [Prov 00000000] [SID 157F]
[ 21:44:11 ] [ Newcamd ] ECM -> dummy (NOT OK) [CAID 0B01] [Prov 00000000] [SID 157F]
[ 21:44:12 ] [ Newcamd ] ECM -> dummy (NOT OK) [CAID 0B01] [Prov 00000000] [SID 157F]
Стигнах до префлашване на геминито, и пак същото. А това с червеното нещо ме притеснява, не съм забелязал дали и преди е излизало.
[ Newcamd ] recv: error! 146: Connection refused
А интересно, когато стартирам мгкам-а, нищо не търси от 0В01, ами само крипто кейс.
[mgcamd] Cryptoworks key(s) not found for caid 0D06 provid c0 keynr 01
[mg0] -> ECM to newcamd 127.0.0.1:34000
[mg0] newcamd route 127.0.0.1:34000 cant decode (3ms)
[newcamd] EMM-S -> 127.0.0.1:34000
[newcamd] EMM answer from 127.0.0.1:34000, 3:82
no cryptoworks RSA found
no cryptoworks RSA found
[mgcamd] Cryptoworks key(s) not found for caid 0D06 provid c0 keynr 01
[mg0] -> ECM to newcamd 127.0.0.1:34000
[mg0] newcamd route 127.0.0.1:34000 cant decode (2ms)
no cryptoworks RSA found
no cryptoworks RSA found
[newcamd] EMM-S -> 127.0.0.1:34000
[newcamd] EMM answer from 127.0.0.1:34000, 3:82
[newcamd] EMM-S -> 127.0.0.1:34000
[newcamd] EMM answer from 127.0.0.1:34000, 3:82
Понеже тая карта стои само в дм500 и от дъжд на вятър я слагам в ДМ800, ако не се ъп, е днес спря да се гледа на дм500 и викам на дм800 да я ъп, но камък. На дм500 няма как да видя какво показват логовете, няма ЛАН-ка.
Някакви идеи? Що ли търси само 0д06? А ако пусна шеринга, гледа си от 0в01, но от шер-а през цици.
In the beginning was dark, and then bang...

fox

#40
25-02-2012, 19:33 Последна редакция: 25-02-2012, 19:36 by fox
Какъв може да е проблема откакто промениха параметрите на 11,895 Астра 23,5 не се отваря нищо на този транспондер.Пробвал съм и с AZBOX HD и с VU UNO , инсталирал съм различни версии на Mgcamd 1.35a , 1.38 .Всички други транспондер се отварят без проблем .


# EMM messages
#    00 don't show any EMMs (default)
#    01 show only valid EMMs
#    02 show valid and bad EMMs with complete data display
M: { 01 }

# ECM messages
#    00 don't show anything about ecm
#    01 normal mode, show pids processed, decoded ecm and cw
#    02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
#    00 disable, no emm pids processed
#    01 enable, emm pids always processed for soft-au and shared cards
#    02 auto, emm started only if channel cant be decoded
#    03 process emm pids for network cards update only
A: { 00 }

# key update (sum 01 or 02 with 04)
#    01 update only new keys, default setting
#    02 update all keys (used for valid PMK checking)
#    04 enable TPS au
#    + tps SID, which pmt pid contains au pid
U: { 02 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)
#    00 /PLUGINS/OpenXCAS/mgcamd
#    01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
#    00 no network (default)
#    01 newcamd netclient
#    02 radegast netclient
#    04 camd3 netclient
#    08 gbox netclient
#    32    cccamd netclient, card list saved as /tmp/cccamd.info
#        (ECM only, supported server version up to 2.1.1, later not work)
G: { 33 }

# network retry, use summ for several options
#    00 disable
#    01 retry every new ecm
#    02 try to connect to offline shares every Q: seconds
#    04 try to detect and fast reconnect to lost (and not used atm) server
#    + XX messages number and YY seconds to reconnect
#    mg will reconnect to server, if no answer to last XX ecm/keepalive or
#    if no answer for last ecm or keepalive sent for YY seconds
#    set to 0 to disable
N: { 01 } 5 30

# network ecm timeout in seconds
K: { 05 }

# newcamd dead routes connect retry, sec
Q: { 6 }

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 02 }

# on screen display type
#    00 No OSD (default)
#    01 neutrino
#    02 enigma
#    03 relook
#    + user password for http auth
O: { 00 } username password

# on screen display Options, summ of:
#    01 show emu ecm
#    02 show network shares messages
#    04 show decoding failed / fta
#    08 show emm keys update
#    + web port to use for osd
S: { 03 } 80

# Log option, summ of:
#    00 off
#    01 network udp log
#    02 log to console
#    04 file, appended ! delete it by yourself, before it eat all your hdd
#    + IP udp-port log-file-name
L: { 04 } 127.0.0.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 20 }

# cache option, summ of:
#    00 Off (default)
#    01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
#    02 Ecm data cache, remember CW for (E:) time
#    04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 02 }

# reread files, summ of:
#    00 No (default)
#    01 reread config file on channel change (including priority and ignore, but not replace/cache)
#    02 reread SoftCam.Key on channel change
#    04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { ff }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips7025(dm800)(vuplus)
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 06 }

# map all 180x nagra caids to 1801
# default is 01
F: { 00 }

фото

#41
25-02-2012, 19:57
Цитат на: fox;145997Какъв може да е проблема откакто промениха параметрите на 11,895 Астра 23,5 не се отваря нищо на този транспондер.Пробвал съм и с AZBOX HD и с VU UNO , инсталирал съм различни версии на Mgcamd 1.35a , 1.38 .Всички други транспондер се отварят без проблем .


# EMM messages
#    00 don't show any EMMs (default)
#    01 show only valid EMMs
#    02 show valid and bad EMMs with complete data display
M: { 01 }

# ECM messages
#    00 don't show anything about ecm
#    01 normal mode, show pids processed, decoded ecm and cw
#    02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
#    00 disable, no emm pids processed
#    01 enable, emm pids always processed for soft-au and shared cards
#    02 auto, emm started only if channel cant be decoded
#    03 process emm pids for network cards update only
A: { 00 }

# key update (sum 01 or 02 with 04)
#    01 update only new keys, default setting
#    02 update all keys (used for valid PMK checking)
#    04 enable TPS au
#    + tps SID, which pmt pid contains au pid
U: { 02 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)
#    00 /PLUGINS/OpenXCAS/mgcamd
#    01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
#    00 no network (default)
#    01 newcamd netclient
#    02 radegast netclient
#    04 camd3 netclient
#    08 gbox netclient
#    32    cccamd netclient, card list saved as /tmp/cccamd.info
#        (ECM only, supported server version up to 2.1.1, later not work)
G: { 33 }

# network retry, use summ for several options
#    00 disable
#    01 retry every new ecm
#    02 try to connect to offline shares every Q: seconds
#    04 try to detect and fast reconnect to lost (and not used atm) server
#    + XX messages number and YY seconds to reconnect
#    mg will reconnect to server, if no answer to last XX ecm/keepalive or
#    if no answer for last ecm or keepalive sent for YY seconds
#    set to 0 to disable
N: { 01 } 5 30

# network ecm timeout in seconds
K: { 05 }

# newcamd dead routes connect retry, sec
Q: { 6 }

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 02 }

# on screen display type
#    00 No OSD (default)
#    01 neutrino
#    02 enigma
#    03 relook
#    + user password for http auth
O: { 00 } username password

# on screen display Options, summ of:
#    01 show emu ecm
#    02 show network shares messages
#    04 show decoding failed / fta
#    08 show emm keys update
#    + web port to use for osd
S: { 03 } 80

# Log option, summ of:
#    00 off
#    01 network udp log
#    02 log to console
#    04 file, appended ! delete it by yourself, before it eat all your hdd
#    + IP udp-port log-file-name
L: { 04 } 127.0.0.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 20 }

# cache option, summ of:
#    00 Off (default)
#    01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
#    02 Ecm data cache, remember CW for (E:) time
#    04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 02 }

# reread files, summ of:
#    00 No (default)
#    01 reread config file on channel change (including priority and ignore, but not replace/cache)
#    02 reread SoftCam.Key on channel change
#    04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { ff }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips7025(dm800)(vuplus)
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 06 }

# map all 180x nagra caids to 1801
# default is 01
F: { 00 }

Пробвай с тези, с тях нямам  проблеми.

M: { 01 }

C: { 01 }

A: { 01 }

U: { 01 }

T: { 00 }

G: { 33 }

N: { 3 }

K: { 02 }

Q: { 300 }

P: { 02 }

O: { 02 }

S: { 02 } 8080

L: { 06 } 192.168.1.1 28007 /tmp/mgcamd.log

E: { 15 }

H: { 07 }

R: { 00 }

D: { 00 }

B: { 00 }

F: { 00 }
AXAS E4HD Ultra 4k(OpenATV 8.0), Офсет 100 см <> Н–Н мотор, Панасоник плазма.

fox

#42
26-02-2012, 20:45
Цитат на: фото;146004Пробвай с тези, с тях нямам  проблеми.

M: { 01 }

C: { 01 }

A: { 01 }

U: { 01 }

T: { 00 }

G: { 33 }

N: { 3 }

K: { 02 }

Q: { 300 }

P: { 02 }

O: { 02 }

S: { 02 } 8080

L: { 06 } 192.168.1.1 28007 /tmp/mgcamd.log

E: { 15 }

H: { 07 }

R: { 00 }

D: { 00 }

B: { 00 }

F: { 00 }
Няма промяна , не се отваря 11,895 Астра 23,5 .Възможно ли е при 72% на 11,895 да е малко за да се отвори? Изчерпаха ми се идеите , възможно ли е проблем с антената?

yavor1

#43
26-02-2012, 20:57
Цитат на: fox;146147Няма промяна , не се отваря 11,895 Астра 23,5 .Възможно ли е при 72% на 11,895 да е малко за да се отвори? Изчерпаха ми се идеите , възможно ли е проблем с антената?
защо
S: { 02 } 8080
опитай S: { 03 } 80

themaster301

#44
26-02-2012, 21:07
Цитат на: fox;146147Няма промяна , не се отваря 11,895 Астра 23,5 .Възможно ли е при 72% на 11,895 да е малко за да се отвори? Изчерпаха ми се идеите , възможно ли е проблем с антената?

Този транспондер е на Skylink и ако си към Зарга , това да е причината да не ти се отваря. Съмнението нараства , ако с тази конфигурация отваряш други пакети.
Парабола 2.2 м. + Multi Satellite Positioner Pace MSP-995 + Mut@nt HD51 + TBS 6903 Professional DVB-S2 Dual Tuner PCI-e Card.
Формат за разпечатване
Нагоре Страници 1 2 3 4 5 ... 8
Действия
SatShop.bg
Ъплоуд център DishPointer Сателитни изстрелвания