Връщане от OpenPli 6.2 към 4.0

[bodurov]

Здравейте колеги,


след като приемникът не беше преинсталиран от 2015 г. имах неблагоразумието преди дни да пробвам версия 6.2 и от тук започнаха проблемите. Опитах да върна отново версия 4.0 но без успех. Инсталира се успешно, но стои на booting и до там. Докато 6.2 се инсталира и зарежда без проблем. OpenATV 6 също отказва да се инсталира. Искам да се върна на 4,0 поне нямах проблеми с нея. Има ли някакъв начин да го направя "принудително".



Често се случва, че след смяна на канал трябва да рестартирам OSCAM за да разкодира канала. Освен това DVB-T тунерът трудно захапва с новите драйвери. Трябва да рестартирам няколко пъти за да сработи. Иначе показва 100% сигнал.  Стриймът не работи добре.


Някакви идеи също така как да оправя поне проблемите с RTL2832U?



Трябва ли да ме притесняват тези грешки (в червено) в лога? Означава ли това, че е повреден флаша нещо?

Код [Маркирай кода] Разшири

PCI2.3->SDRAM window: 512 MB
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux video capture interface: v2.00
Advanced Linux Sound Architecture Driver Initialized.
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0xd0000000-0xefffffff]
pci_bus 0000:00: root bus resource [io  0x0400-0x83ff]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [mem 0x10510000-0x1051ffff]
pci_bus 0000:01: root bus resource [io  0x8400-0x87ff]
pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
pci 0000:01:00.0: [14e4:8602] type 00 class 0x01010f
PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
pci 0000:01:00.0: reg 24: [mem 0x00000000-0x00000fff]
pci 0000:01:00.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff]
pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref]
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource upg
FS-Cache: Loaded
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
fuse init (API version 7.20)
msgmni has been set to 567
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A
serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A
loop: module loaded
sata_brcmstb 0000:01:00.0: version 4.0
__clk_enable: sata [1]
PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
sata_brcmstb 0000:01:00.0: setting latency timer to 64
scsi0 : sata_brcmstb
scsi1 : sata_brcmstb
ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
Broadcom STB NAND controller (BrcmNand Controller)
bcmemac: Broadcom STB 10/100 EMAC driver v3.0
bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:16:b4:04:af:b2)
bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
usbcore: registered new interface driver zd1201
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
__clk_enable: usb [1]
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
usbcore: registered new interface driver btusb
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
NET: Registered protocol family 17
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Bluetooth: HIDP socket layer initialized
Key type dns_resolver registered
EBI CS1: setting up NAND flash (primary)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
B4: NandSelect=50000200, nandConfig=16152300, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecda1095
After: NandSelect=50000200, nandConfig=16152300
Block size=00020000, erase shift=17
NAND Config: Reg=16152300, chipSize=256 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 5363444f
timing2 not adjusted: 00000fc6
eccLevel=15, 1Ksector=0, oob=16
nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000
BrcmNAND mfg ec da Samsung K9F2G08U0A 256MB on CS1

Found NAND on CS1: ACC=d7ff1010, cfg=16152300, flashId=ecda1095, tim1=5363444f, tim2=00000fc6
BrcmNAND version = 0x0302 256MB @00000000
B4: NandSelect=50000200, nandConfig=16152300, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecda1095
After: NandSelect=50000200, nandConfig=16152300
Found NAND flash on Chip Select 1, chipSize=256MB, usable size=256MB, base=0
brcmnand_scan: B4 nand_select = 50000200
brcmnand_scan: After nand_select = 50000200
page_shift=11, bbt_erase_shift=17, chip_shift=28, phys_erase_shift=17
Brcm NAND controller version = 3.2 NAND flash size 256MB @10000000
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan:  mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
[COLOR=Red]brcmnand_default_bbt: bbt_td = bbt_main_descr
Bad block table Bbt0 found at page 0001ffc0, version 0x01 for chip on CS1
Bad block table 1tbB found at page 0001ff80, version 0x01 for chip on CS1
nand_read_bbt: Bad block at 0x01140000
nand_read_bbt: Bad block at 0x04ac0000
nand_read_bbt: Bad block at 0x07740000
nand_read_bbt: Bad block at 0x09440000
nand_read_bbt: Bad block at 0x0f840000
Adjust partition complete size from entire device to ff00000 to avoid overlap with BBT reserved space[/COLOR]
Adjust partition rootfs size from entire device to f900000 to avoid overlap with BBT reserved space
Creating 3 MTD partitions on &quot;brcmnand.0&quot;:
0x000000000000-0x00000ff00000 : &quot;complete&quot;
0x000000000000-0x000000600000 : &quot;kernel&quot;
0x000000600000-0x00000ff00000 : &quot;rootfs&quot;
PM: CP0 COUNT/COMPARE frequency depends on divisor
UBI: attaching mtd2 to ubi0
ata1: SATA link down (SStatus 4 SControl 300)
usb 1-2: new high-speed USB device number 2 using ehci-brcm
ata2: SATA link down (SStatus 4 SControl 300)
usb 4-1: new full-speed USB device number 2 using ohci-brcm
usb 4-1: device descriptor read/64, error -62
usb 4-1: device descriptor read/64, error -62
usb 4-1: new full-speed USB device number 3 using ohci-brcm
usb 4-1: device descriptor read/64, error -62
usb 4-1: device descriptor read/64, error -62
usb 4-1: new full-speed USB device number 4 using ohci-brcm
UBI: scanning is finished
UBI: attached mtd2 (name &quot;rootfs&quot;, size 249 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 1987, bad PEBs: 5, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1716067110
UBI: available PEBs: 0, total reserved PEBs: 1987, PEBs reserved for bad PEB handling: 35
ALSA device list:
  No soundcards found.
Warning: unable to open an initial console.
UBI: background thread &quot;ubi_bgt0d&quot; started, PID 49
UBIFS: background thread &quot;ubifs_bgt0_0&quot; started, PID 50
UBIFS: mounted UBI device 0, volume 0, name &quot;rootfs&quot;(null)
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 245952512 bytes (234 MiB, 1937 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
UBIFS: reserved for root: 0 bytes (0 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID F289370E-7A03-4762-923E-26DFF0895ADE, small LPT model
VFS: Mounted root (ubifs filesystem) on device 0:10.
devtmpfs: mounted
Freeing unused kernel memory: 316k freed
usb 4-1: device not accepting address 4, error -62
usb 4-1: new full-speed USB device number 5 using ohci-brcm
usb 4-1: device not accepting address 5, error -62
hub 4-0:1.0: unable to enumerate USB device on port 1
usbcore: registered new interface driver tpm
dvb: module_layout: kernel tainted.
Disabling lock debugging due to kernel taint
Console: switching to colour frame buffer device 160x45
input: dreambox remote control (native) as /devices/virtual/input/input0
input: dreambox advanced remote control (native) as /devices/virtual/input/input1
DVB: registering new adapter (dvb0)
platform dvb0.0: DVB: registering adapter 0 frontend 0 (DVB-S2)...
platform dvb0.0: DVB: registering adapter 0 frontend 1 (DVB-S2)...
input: front panel as /devices/virtual/input/input2
dvb-usb: found a 'RTL2832U DVB-T USB DEVICE' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (RTL2832U DVB-T USB DEVICE)
usb 1-2: DVB: registering adapter 1 frontend 0 (Realtek DVB-T RTL2832)...
dvb-usb: RTL2832U DVB-T USB DEVICE successfully initialized and connected.
usbcore: registered new interface driver dvb_usb_rtl2832u
usbcore: registered new interface driver dvb_usb_rtl28xxu
Console: switching to colour dummy device 80x25
NET: Registered protocol family 10
platform dvb0.0: DVB: registering adapter 0 frontend 2 (vtuner)...

[yavor1]

Не си написал за кой приемник иде реч, дали си с коректния буутлоадер, онлайн опитва ли да ъпнеш? Префлашваш ли с този имидж и желау ли да се префлашне?



http://downloads.openpli.org/builds/et9x00/openpli-4-release-et9x00-20180625_usb.zip

[bodurov]

Не си написал за кой приемник иде реч, дали си с коректния буутлоадер, онлайн опитва ли да ъпнеш? Префлашваш ли с този имидж и желау ли да се префлашне?



http://downloads.openpli.org/builds/et9x00/openpli-4-release-et9x00-20180625_usb.zip

Точно за XTrend ET9200 става въпрос. Пробвах точно с този имидж. Флашва се, изписва на дисплея Flashing completed ... рестартира се и тръгва да зарежда, но стои на booting...


Пробвах и с останалите по-стари имиджи на страницата, но положението е същото. Единствено приема 6.2 с нея се инсталира, буутва и всичко е наред.


Как да го ъпна онлайн? Ако му дам Актуализация на софтуера ми изписва Няма намерени обновления.

[bodurov]

Намерих менюто за онлайн инсталиране на имидж. Не знаех, че е добавена такава опция. Започна инсталирането, но със същият резултат. Явно отказва да приеме по-стара версия.


Най-накрая успях да го излъжа като преименувах файла noforce на force. Инсталира се без проблем и зареди успешно.

[demmlik]