Чат

🕑 ↗
За да пишеш, трябва да си влязъл в профила си.

Софтуер за IXUSS ONE

Започната от Devil M, 03-02-2013, 15:50

« назад - напред »

0 Потребители и 1 гост преглеждат тази тема.



aidyn

Здравейте! Искам да помоля за помощ. Взех си IXUSS ONE   openatv4.2.
 Това ми е първи приемник, базиран на Линукс. Не мога да му подкарам шеринга.
Свалих TSpanel, инсталирах Mgcamd 1.38. Сложих cccamd.list в директорията var/ keys .....Направих всичко което е писано в нета, но не тръгва. В смисъл, сървърът е активен, но не отваря нищо....Къде бъркам?

miros123

Постни си mg_cfg
Pasat Ф140, LNB Inverto 0,3db, Super PowerJack 12", NP-601, {DM500s, DM800PVR} - clone {Gemini - mbox 0.4}, {Vu+ solo2}, {4[FONT="]°[/FONT]W-57[FONT="]°[/FONT]E}

tibuzdrev

Първо си сложи Mgcamd 1.35
 после питай

aidyn

Цитат на: miros123;344399Постни си mg_cfg

# EMM messages 
# 00 don't show any EMMs (default) 
# 01 show only valid EMMs 
# 02 show valid and bad EMMs with complete data display 
M: { 01 } 

# ECM messages 
# 00 don't show anything about ecm 
# 01 normal mode, show pids processed, decoded ecm and cw 
# 02 verbose mode, show valid and bad ECMs with data 
C: { 02 } 

# AU 
# 00 disable, no emm pids processed 
# 01 enable, emm pids always processed for soft-au and shared cards 
# 02 auto, emm started only if channel cant be decoded 
# 03 process emm pids for network cards update only 
A: { 01 } 

# key update (sum 01 or 02 with 04) 
# 01 update only new keys, default setting 
# 02 update all keys (used for valid PMK checking) 
# 04 enable TPS au 
# + tps SID, which pmt pid contains au pid 
U: { 01 } 0x12c0 

# config files folder (softcam, autoroll, ignore/priority) 
# 00 files in /var/keys 
# 01 files in /tmp 
T: { 00 } 

# network mode, use summ for several clients 
# 00 no network (default) 
# 01 newcamd netclient 
# 02 radegast netclient 
# 04 camd3 netclient 
# 08 gbox netclient 
# 32 cccamd netclient, card list saved as /tmp/cccamd.info 
# (ECM only, supported server version up to 2.1.1, later not work) 
G: { 32 } 

# network retry, use summ for several options 
# 00 disable 
# 01 retry every new ecm 
# 02 try to connect to offline shares every Q: seconds 
# 04 try to detect and fast reconnect to lost (and not used atm) server 
# + XX messages number and YY seconds to reconnect 
# mg will reconnect to server, if no answer to last XX ecm/keepalive or 
# if no answer for last ecm or keepalive sent for YY seconds 
# set to 0 to disable 
N: { 07 } 5 30 

# network ecm timeout in seconds 
K: { 05 } 

# newcamd dead routes connect retry, sec 
Q: { 600 } 

# network shares priority 
# 00 gbox, newcamd, cccamd, radegast, camd3 (default) 
# 01 camd3, radegast, cccamd, gbox, newcamd 
# 02 cccamd, newcamd, camd3, gbox, radegast 
P: { 02 } 

# on screen display type 
# 00 No OSD (default) 
# 01 neutrino 
# 02 enigma 
# 03 relook 
# + user password for http auth 
O: { 00 } username password 

# on screen display Options, summ of: 
# 01 show emu ecm 
# 02 show network shares messages 
# 04 show decoding failed / fta 
# 08 show emm keys update 
# + web port to use for osd 
S: { 03 } 80 

# Log option, summ of: 
# 00 off 
# 01 network udp log 
# 02 log to console 
# 04 file, appended ! delete it by yourself, before it eat all your hdd 
# + IP udp-port log-file-name 
L: { 02 } 172.16.1.1 28007 /tmp/mgcamd.log 

# keep ecm cache, seconds 
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory, 
# for openbox/elanvision users with remote shares make sense to set it higher than default value, 
# to not hammer cards while timeshifting or playing crypted recordings. 
E: { 15 } 

# cache option, summ of: 
# 00 Off (default) 
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list 
# 02 Ecm data cache, remember CW for (E time 
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart 
H: { 07 } 

# reread files, summ of: 
# 00 No (default) 
# 01 reread config file on channel change (including priority and ignore, but not replace/cache) 
# 02 reread SoftCam.Key on channel change 
# 04 reread SoftCam.Key if file changed 
R: { 04 } 

# debug, summ of 
# 00 off (default) 
# 01 debug ecm 
# 02 debug emm 
# 04 debug network ecm 
# 08 debug network emm 
# 16 debug network login 
# 32 show mem/cpu stats every 1 min 
# 64 add timestamp to log messages 
D: { 00 } 

# box type 
# 00 autodetect, change only if you think wrong type detected. 
# 01 dbox2 
# 02 dreambox 
# 03 triple-dragon 
# 04 relook 
# 05 openbox 
# 06 dreambox/mips 
# 08 stapi/kathrein 
# 09 stapi/ipbox 
# 11 stapi/openbox 
B: { 00 } 

# map all 180x nagra caids to 1801 
# default is 01 
F: { 00 } 



Това ли е?

miros123

#6
B: { 06 }

Сигурен ли си, че кама ти е стартиран. Ръчно ли го добавя или от сървъра. Да не си пропуснал права 755 на бин файла и скрипта. През конзолата с команда top виж дали имаш редове с име mgcamd1.38 да се движат.

C: { 01 }
A: { 02 }
Pasat Ф140, LNB Inverto 0,3db, Super PowerJack 12", NP-601, {DM500s, DM800PVR} - clone {Gemini - mbox 0.4}, {Vu+ solo2}, {4[FONT="]°[/FONT]W-57[FONT="]°[/FONT]E}

aidyn

Цитат на: miros123;344413B: { 06 }

Сигурен ли си, че кама ти е стартиран. Ръчно ли го добавя или от сървъра. Да не си пропуснал права 755 на бин файла и скрипта. През конзолата с команда top виж дали имаш редове с име mgcamd1.38 да се движат.

C: { 01 }
A: { 02 }

Мерси много!!! Стана, бях направил всичко, освен B: { 06 }
:;810:;810:;810

SatShop.bg
Ъплоуд център DishPointer Сателитни изстрелвания