Здравейте, взех си карта Conax на Satellitebg и не ми разкодира каналите, къде да търся проблема?
Ето лога на oscam-a:
2011/04/13 0:54:04 2AAC6850 s >> OSCam << cardserver started version 1.00-unstable_svn, build #4574 (mips-tuxbox-linux)
2011/04/13 0:54:04 2AAC6850 s version=1.00-unstable_svn, build #4574, system=mips-tuxbox-linux, nice=-1
2011/04/13 0:54:04 2AAC6850 s client max. idle=120 sec, debug level=0
2011/04/13 0:54:04 2AAC6850 s max. logsize=32 Kb
2011/04/13 0:54:04 2AAC6850 s client timeout=5000 ms, fallback timeout=2500 ms, cache delay=120 ms
2011/04/13 0:54:04 2AAC6850 s auth size=4976
2011/04/13 0:54:04 2AAC6850 s services reloaded: 0 services freed, 1 services loaded
2011/04/13 0:54:04 2AAC6850 s userdb reloaded: 1 accounts loaded, 0 expired, 0 disabled
2011/04/13 0:54:04 2AAC6850 s signal handling initialized (type=sysv)
2011/04/13 0:54:04 2AAC6850 s 37 service-id's loaded
2011/04/13 0:54:04 2AAC6850 s can't open file "/var/tuxbox/config/oscam.tiers" (err=2), no tier-id's loaded
2011/04/13 0:54:04 2AAC6850 s can't open file "/var/tuxbox/config/oscam.provid" (err=2), no provids's loaded
2011/04/13 0:54:04 2AAC6850 s can't open file "/var/tuxbox/config/oscam.ird" (errno=2) irdeto guessing not loaded
2011/04/13 0:54:04 2AAC6850 s monitor: initialized (fd=8, port=988)
2011/04/13 0:54:04 2AAC6850 s camd33: disabled
2011/04/13 0:54:04 2AAC6850 s camd35: disabled
2011/04/13 0:54:04 2AAC6850 s cs378x: disabled
2011/04/13 0:54:04 2AAC6850 s newcamd: disabled
2011/04/13 0:54:04 2AAC6850 s cccam: disabled
2011/04/13 0:54:04 2AAC6850 s radegast: disabled
2011/04/13 0:54:04 2AAC6850 s http thread started
2011/04/13 0:54:04 2AAC6850 s creating thread for device /dev/sci0
2011/04/13 0:54:04 2AAC6850 s loadbalancer: can't read from file /tmp/.oscam/stat
2011/04/13 0:54:04 2AAC6850 s waiting for local card init
2011/04/13 0:54:04 2AEFF4B0 h HTTP Server listening on port 8888
2011/04/13 0:54:04 2AFFF4B0 r reader thread started (thread=2AFFF4B0, label=satellitebg, device=/dev/sci0, detect=cd, mhz=500, cardmhz=357)
2011/04/13 0:54:04 2AFFF4B0 r satellitebg card detected
2011/04/13 0:54:05 2AFFF4B0 r ATR: 3B 34 94 00 30 42 30 30
2011/04/13 0:54:07 2AFFF4B0 r Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz
2011/04/13 0:54:08 2AFFF4B0 r type: Conax, caid: 0B01, serial: ХХХХХХХХХХ, hex serial: ХХХХХХХ, card: v64
2011/04/13 0:54:08 2AFFF4B0 r Providers: 1
2011/04/13 0:54:08 2AFFF4B0 r Provider: 1 Provider-Id: 000000
2011/04/13 0:54:08 2AFFF4B0 r Provider: 1 SharedAddress: 00000000
2011/04/13 0:54:08 2AFFF4B0 r found cardsystem
2011/04/13 0:54:08 2AFFF4B0 r Package: 1, id: 1010, date: 2011/04/04 - 2011/04/09, name: Preview1
2011/04/13 0:54:08 2AFFF4B0 r [conax-reader] ready for requests
2011/04/13 0:54:08 2AAC6850 s init for all local cards done
2011/04/13 0:54:08 2AAC6850 s anti cascading disabled
2011/04/13 0:54:08 2B0FF4B0 c plain dvbapi-client granted (user, au=satellitebg)
2011/04/13 0:54:08 2B0FF4B0 c dvbapi: reread priority file oscam.dvbapi
2011/04/13 0:54:08 2B0FF4B0 c dvbapi: 2 entries read from oscam.dvbapi
2011/04/13 0:54:12 2B0FF4B0 c dvbapi: [ADD PID 0] CAID: 0D06 ECM_PID: 0513 PROVID: 000000
2011/04/13 0:54:12 2B0FF4B0 c dvbapi: [ADD PID 1] CAID: 0B01 ECM_PID: 0522 PROVID: 000000
2011/04/13 0:54:12 2B0FF4B0 c dvbapi: new program number: 1522 (0D06:1522 unknown)
2011/04/13 0:54:12 2B0FF4B0 c dvbapi: try pids again #1
2011/04/13 0:54:12 2B0FF4B0 c user (0B01&000000/1522/67:1CAC): not found (94 ms) (of 1 avail 1)
2011/04/13 0:54:12 2B0FF4B0 c dvbapi: try pids again #2
2011/04/13 0:54:12 2B0FF4B0 c user (0B01&000000/1522/67:E401): not found (85 ms) (of 1 avail 1)
Картата ти се нуждае от ъпдейт
Цитат2011/04/13 0:54:08 2AFFF4B0 r Package: 1, id: 1010, date: 2011/04/04 - 2011/04/09, name: Preview1
Здравейте, пробвах какво ли не, но каналите не се отварят и картата не иска да се ъпдейнте започвам да се съмнявам във версията на oscam. Приемника ми е DM500 HD с Enigma2 и Gemini 5.1. Ако някои е подкарал такава карта то със коя версия на oscam е станало и от къде я е изтеглил?
Иначе ето с какво се опитвам да я подкарам:
oscam.conf
[global]
nice=-1
logfile=/tmp/oscam.log
disablelog=0
disableuserfile=1
maxlogsize=32
waitforcards=1
saveinithistory = 1
preferlocalcards=1
cachedelay=120
[monitor]
port = 988
aulow = 120
monlevel = 4
nocrypt = 127.0.0.1,192.168.1.1-192.168.1.255
[webif]
httpport=8888
httpallowed=127.0.0.1,192.168.1.1-192.168.1.255
[dvbapi]
enabled=1
boxtype=dreambox
user=user
au=1
ignore = 0d06:000000
priority = 0B01:000000
oscam.user
[account]
user = user
group = 1
uniq = 0
au= satellitebg
monlevel = 4
keepalive = 1
oscam.dvbapi
P: 0B01:000000
I: 0d06:000000
оscam.server
[reader]
label = satellitebg
enable = 1
protocol = internal
device = /dev/sci1
pincode = 0000
services = SatelliteBG
fallback = 1
caid = 0b01
detect = cd
mhz = 500
cardmhz = 357
ident = 0b01:000000
group = 1
emmcache = 1,3,2
lb_weight = 100
Цитат на: piris;95395Приемника ми е DM500 HD с Enigma2 и Gemini 5.1.
Цитат на: piris;95395оscam.server
[reader]
label = satellitebg
enable = 1
protocol = internal
device = /dev/sci1
pincode = 0000
services = SatelliteBG
fallback = 1
caid = 0b01
detect = cd
mhz = 500
cardmhz = 357
ident = 0b01:000000
group = 1
emmcache = 1,3,2
lb_weight = 100
Редактирай, трябва да ти е:
device = /dev/sci0[COLOR=Black]fallback = 0[/COLOR]А за сървисите трябва да си сигурен, че си ги oписал всичките в oscam.services.
Цитат на: piris;95395[dvbapi]
enabled=1
boxtype=dreambox
user=user
au=1
ignore = 0d06:000000
priority = 0B01:000000
Изтрий тези 2 реда, те се задават в oscam.dvbapi, а като споменах oscam.dvbapi, махни игнора на 0d06, задаването на приоритет е достатъчно за да търси първо твоята карта.
Цитат на: piris;95395Здравейте, пробвах какво ли не, но каналите не се отварят и картата не иска да се ъпдейнте започвам да се съмнявам във версията на oscam. Приемника ми е DM500 HD с Enigma2 и Gemini 5.1. Ако някои е подкарал такава карта то със коя версия на oscam е станало и от къде я е изтеглил?
Иначе ето с какво се опитвам да я подкарам:
oscam.conf[global]
nice=-1
logfile=/tmp/oscam.log
disablelog=0
disableuserfile=1
maxlogsize=32
waitforcards=1
saveinithistory = 1
preferlocalcards=1
cachedelay=120
Сложи разстояние между равното ето така, иначе няма да тръгне, и където пишеш в оскам винаги да има разтояние между равното и отделните команди
oscam.conf[global]
nice = -1
logfile = /tmp/oscam.log
disablelog = 0
disableuserfile = 1
maxlogsize = 32
waitforcards = 1
saveinithistory = 1
preferlocalcards = 1
cachedelay = 120
благодаря за съветите, ще коригирам, а относно версията на oscam коя е стабилна и от къде да я изтегля, защото от стотиците версий незная тази която съм инсталирал дали е читава, а тя е oscam version 1.00-unstable_svn, build #4574 ,и още веднъж благодаря за бързите отговори.
Здравейте,
преди 3-4 дни взех карта на Сателайт БГ, пробвах с NewCS + CCCam, не можах да подкарам. Тръгна сама с Gbox и я оставих така. Днес обаче спря телевизията. Търсих навсякъде нещо за NewCS + CCcam, или поне за Gbox нищо не можах да открия. Някой може ли да даде конфигурационни файлове? Става въпрос за DM800. До сега си глеах ИРДЕТО и не съм имал подобни ядове...
Разбрах също, че е възможно и само с CCcam да върви, ако е така бих го предпочел.
Мерси предварително!
Здравейте отново, след направените промени каналите все още не се отварят, предполагам защото не се е ъпдейтнала, каква може да е причината и как да разбера дали oscam-a прави опити за ъпдейт на картата?
Ето и лога:
2011/04/17 23:06:53 2AAC6850 s >> OSCam << cardserver started version 1.00-unstable_svn, build #4574 (mips-tuxbox-linux)
2011/04/17 23:06:53 2AAC6850 s version=1.00-unstable_svn, build #4574, system=mips-tuxbox-linux, nice=-1
2011/04/17 23:06:53 2AAC6850 s client max. idle=120 sec, debug level=0
2011/04/17 23:06:53 2AAC6850 s max. logsize=32 Kb
2011/04/17 23:06:53 2AAC6850 s client timeout=5000 ms, fallback timeout=2500 ms, cache delay=120 ms
2011/04/17 23:06:53 2AAC6850 s auth size=4976
2011/04/17 23:06:53 2AAC6850 s services reloaded: 0 services freed, 1 services loaded
2011/04/17 23:06:53 2AAC6850 s userdb reloaded: 1 accounts loaded, 0 expired, 0 disabled
2011/04/17 23:06:53 2AAC6850 s signal handling initialized (type=sysv)
2011/04/17 23:06:53 2AAC6850 s 37 service-id's loaded
2011/04/17 23:06:53 2AAC6850 s can't open file "/var/tuxbox/config/oscam.tiers" (err=2), no tier-id's loaded
2011/04/17 23:06:53 2AAC6850 s can't open file "/var/tuxbox/config/oscam.provid" (err=2), no provids's loaded
2011/04/17 23:06:53 2AAC6850 s can't open file "/var/tuxbox/config/oscam.ird" (errno=2) irdeto guessing not loaded
2011/04/17 23:06:53 2AAC6850 s monitor: initialized (fd=8, port=988)
2011/04/17 23:06:53 2AAC6850 s camd33: disabled
2011/04/17 23:06:53 2AAC6850 s camd35: disabled
2011/04/17 23:06:53 2AAC6850 s cs378x: disabled
2011/04/17 23:06:53 2AAC6850 s newcamd: disabled
2011/04/17 23:06:53 2AAC6850 s cccam: disabled
2011/04/17 23:06:53 2AAC6850 s radegast: disabled
2011/04/17 23:06:53 2AAC6850 s http thread started
2011/04/17 23:06:53 2AAC6850 s creating thread for device /dev/sci0
2011/04/17 23:06:53 2AAC6850 s loadbalancer: can't read from file /tmp/.oscam/stat
2011/04/17 23:06:53 2AAC6850 s waiting for local card init
2011/04/17 23:06:53 2AEFF4B0 h HTTP Server listening on port 8888
2011/04/17 23:06:53 2AFFF4B0 r reader thread started (thread=2AFFF4B0, label=satellitebg, device=/dev/sci0, detect=cd, mhz=500, cardmhz=357)
2011/04/17 23:06:53 2AFFF4B0 r satellitebg card detected
2011/04/17 23:06:54 2AFFF4B0 r ATR: 3B 34 94 00 30 42 30 30
2011/04/17 23:06:56 2AFFF4B0 r Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz
2011/04/17 23:06:57 2AFFF4B0 r type: Conax, caid: 0B01, serial: **********, hex serial: ********, card: v64
2011/04/17 23:06:57 2AFFF4B0 r Providers: 1
2011/04/17 23:06:57 2AFFF4B0 r Provider: 1 Provider-Id: 000000
2011/04/17 23:06:57 2AFFF4B0 r Provider: 1 SharedAddress: 00000000
2011/04/17 23:06:57 2AFFF4B0 r found cardsystem
2011/04/17 23:06:57 2AFFF4B0 r Package: 1, id: 1010, date: 2011/04/04 - 2011/04/09, name: Preview1
2011/04/17 23:06:57 2AFFF4B0 r [conax-reader] ready for requests
2011/04/17 23:06:57 2AAC6850 s init for all local cards done
2011/04/17 23:06:57 2AAC6850 s anti cascading disabled
2011/04/17 23:06:57 2B0FF4B0 c plain dvbapi-client granted (user, au=satellitebg)
2011/04/17 23:06:57 2B0FF4B0 c dvbapi: 1 entries read from oscam.dvbapi
2011/04/17 23:07:00 2B0FF4B0 c dvbapi: [ADD PID 0] CAID: 0D06 ECM_PID: 04FD PROVID: 000000
2011/04/17 23:07:00 2B0FF4B0 c dvbapi: [ADD PID 1] CAID: 0B01 ECM_PID: 0520 PROVID: 000000
2011/04/17 23:07:00 2B0FF4B0 c dvbapi: new program number: 151A (0D06:151A unknown)
2011/04/17 23:07:00 2B0FF4B0 c user (0B01&000000/151A/67:EBA3): not found (94 ms) (of 1 avail 1)
2011/04/17 23:07:01 2B0FF4B0 c dvbapi: try pids again #1
2011/04/17 23:07:01 2B0FF4B0 c user (0D06&0000C0/151A/B4:5680): rejected group (120 ms) (of 0 avail 0) (no matching reader)
2011/04/17 23:07:02 2B0FF4B0 c user (0B01&000000/151A/67:C63C): not found (88 ms) (of 1 avail 1)
2011/04/17 23:07:02 2B0FF4B0 c dvbapi: try pids again #2
2011/04/17 23:07:02 2B0FF4B0 c user (0D06&0000C0/151A/B4:2BBB): rejected group (120 ms) (of 0 avail 0) (no matching reader)
2011/04/17 23:07:06 2B0FF4B0 c user (0B01&000000/151A/67:EBA3): timeout (5031 ms) (of 0 avail 0)
2011/04/17 23:07:07 2B0FF4B0 c dvbapi: try pids again #3
2011/04/17 23:07:07 2B0FF4B0 c dvbapi: can't decode channel
2011/04/17 23:07:07 2B0FF4B0 c user (0B01&000000/151A/67:C63C): timeout (5025 ms) (of 0 avail 0)
2011/04/17 23:07:11 2B0FF4B0 c dvbapi: can't decode channel
2011/04/17 23:07:11 2B0FF4B0 c user (0D06&0000C0/151A/B4:2BBB): timeout (5095 ms) (of 0 avail 0)
2011/04/17 23:12:12 2B0FF4B0 c dvbapi: [ADD PID 0] CAID: 0D06 ECM_PID: 052D PROVID: 000000
2011/04/17 23:12:12 2B0FF4B0 c dvbapi: [ADD PID 1] CAID: 0B01 ECM_PID: 050A PROVID: 000000
2011/04/17 23:12:12 2B0FF4B0 c dvbapi: new program number: 1529 (0D06:1529 unknown)
2011/04/17 23:12:12 2B0FF4B0 c user (0B01&000000/1529/67:2D2B): rejected group (120 ms) (of 0 avail 0) (no matching reader)
2011/04/17 23:12:12 2B0FF4B0 c dvbapi: try pids again #1
2011/04/17 23:12:12 2B0FF4B0 c user (0D06&0000C0/1529/B4:062F): rejected group (120 ms) (of 0 avail 0) (no matching reader)
2011/04/17 23:12:16 2B0FF4B0 c user (0B01&000000/1529/67:3E3D): rejected group (120 ms) (of 0 avail 0) (no matching reader)
2011/04/17 23:12:17 2B0FF4B0 c dvbapi: try pids again #2
2011/04/17 23:12:17 2B0FF4B0 c user (0D06&0000C0/1529/B4:BAA3): rejected group (120 ms) (of 0 avail 0) (no matching reader)
2011/04/17 23:12:18 2B0FF4B0 c user (0B01&000000/1529/67:2D2B): timeout (5031 ms) (of 0 avail 0)
2011/04/17 23:12:22 2B0FF4B0 c dvbapi: try pids again #3
2011/04/17 23:12:22 2B0FF4B0 c dvbapi: can't decode channel
2011/04/17 23:12:22 2B0FF4B0 c user (0B01&000000/1529/67:3E3D): timeout (5031 ms) (of 0 avail 0)
2011/04/17 23:12:23 2B0FF4B0 c dvbapi: can't decode channel
2011/04/17 23:12:23 2B0FF4B0 c user (0D06&0000C0/1529/B4:BAA3): timeout (5043 ms) (of 0 avail 0)
2011/04/17 23:12:27 2B0FF4B0 c dvbapi: new program number: 1582 (0000:1582 unknown)
Цитат на: itzko;95564Някой може ли да даде конфигурационни файлове? Става въпрос за DM800.
Инсталираш оскам и четеш пост №4 от тази тема!
@pirisPackage: 1, id: 1010, date: 2011/04/04 - 2011/04/09, name: Preview1
Картата не ти е ъпната, гледай датата!
Звънни по телефона или се обърни към най-близкия представител!
Картите до колкото знам се продават с 5 дни безплатно гледане, след това трябва да се ъпне.
Здравейте,
отново аз... Инсталирах OSCAM - метнах bin-а в /usr/bin, конфигурационните файлове във /var/tuxbox/config Няма да слагам тук съдържанието им, тъй като е копирано 1:1 от темите тук. Ето какво показва лог файла:
>> OSCam << cardserver started at Mon Apr 18 22:02:27 2011
-------------------------------------------------------------------------------
2011/04/18 22:02:27 2AACA000 s >> OSCam << cardserver started version 1.00-unstable_svn, build #5047 (mips-tuxbox-linux)
2011/04/18 22:02:27 2AACA000 s version=1.00-unstable_svn, build #5047, system=mips-tuxbox-linux, nice=-1
2011/04/18 22:02:27 2AACA000 s client max. idle=120 sec, debug level=0
2011/04/18 22:02:27 2AACA000 s max. logsize=32 Kb
2011/04/18 22:02:27 2AACA000 s client timeout=5000 ms, fallback timeout=2500 ms, cache delay=120 ms
2011/04/18 22:02:27 2AACA000 s auth size=5032
2011/04/18 22:02:27 2AACA000 s services reloaded: 0 services freed, 1 services loaded
2011/04/18 22:02:27 2AACA000 s userdb reloaded: 1 accounts loaded, 0 expired, 0 disabled
2011/04/18 22:02:27 2AACA000 s signal handling initialized (type=sysv)
2011/04/18 22:02:27 2AACA000 s 33 service-id's loaded
2011/04/18 22:02:27 2AACA000 s can't open file "/var/tuxbox/config/oscam.tiers" (err=2 No such file or directory), no tier-id's loaded
2011/04/18 22:02:27 2AACA000 s can't open file "/var/tuxbox/config/oscam.provid" (err=2 No such file or directory), no provids's loaded
2011/04/18 22:02:27 2AACA000 s can't open file "/var/tuxbox/config/oscam.ird" (errno=2 No such file or directory) irdeto guessing not loaded
2011/04/18 22:02:27 2AACA000 s monitor: initialized (fd=7, port=988)
2011/04/18 22:02:27 2AACA000 s camd33: disabled
2011/04/18 22:02:27 2AACA000 s camd35: disabled
2011/04/18 22:02:27 2AACA000 s cs378x: disabled
2011/04/18 22:02:27 2AACA000 s newcamd: disabled
2011/04/18 22:02:27 2AACA000 s cccam: disabled
2011/04/18 22:02:27 2AACA000 s radegast: disabled
2011/04/18 22:02:27 2AACA000 s http thread started
2011/04/18 22:02:27 2AACA000 s creating thread for device /dev/sci0
2011/04/18 22:02:27 2AACA000 s waiting for local card init
2011/04/18 22:02:27 2BDD7500 h HTTP Server listening on port 8888
2011/04/18 22:02:27 2C5D7500 r reader thread started (thread=2C5D7500, label=satellitebg, device=/dev/sci0, detect=cd, mhz=500, cardmhz=357)
2011/04/18 22:02:27 2C5D7500 r satellitebg card detected
2011/04/18 22:02:28 2C5D7500 r ATR: 3B 34 94 00 30 42 30 30
2011/04/18 22:02:30 2C5D7500 r Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz
2011/04/18 22:02:31 2C5D7500 r type: Conax, caid: 0B01, serial: 2033008760, hex serial: 792d4078, card: v64
2011/04/18 22:02:31 2C5D7500 r Providers: 1
2011/04/18 22:02:31 2C5D7500 r Provider: 1 Provider-Id: 000000
2011/04/18 22:02:31 2C5D7500 r Provider: 1 SharedAddress: 00000000
2011/04/18 22:02:31 2C5D7500 r found cardsystem conax
2011/04/18 22:02:31 2C5D7500 r Package: 1, id: 1010, date: 2011/04/11 - 2011/04/16, name: Preview1
2011/04/18 22:02:31 2C5D7500 r [conax-reader] ready for requests
2011/04/18 22:02:32 2AACA000 s init for all local cards done
2011/04/18 22:02:32 2AACA000 s anti cascading disabled
2011/04/18 22:02:32 2CDD7500 c plain dvbapi-client granted (user, au=on (1 reader))
2011/04/18 22:02:32 2CDD7500 c dvbapi: reread priority file oscam.dvbapi
2011/04/18 22:02:32 2CDD7500 c dvbapi: 1 entries read from oscam.dvbapi
2011/04/18 22:02:32 2CDD7500 c dvbapi: [ADD PID 0] CAID: 0D06 ECM_PID: 04FD PROVID: 000000
2011/04/18 22:02:32 2CDD7500 c dvbapi: [ADD PID 1] CAID: 0B01 ECM_PID: 0520 PROVID: 000000
2011/04/18 22:02:32 2CDD7500 c dvbapi: new program number: 151A (0D06:151A unknown)
2011/04/18 22:02:32 2CDD7500 c user (0B01&000000/151A/67:067B): not found (92 ms) by satellitebg (of 1 avail 1)
2011/04/18 22:02:33 2CDD7500 c dvbapi: try pids again #1
2011/04/18 22:02:33 2CDD7500 c user (0D06&0000C0/151A/B4:E7D4): rejected group (121 ms) (of 0 avail 0) (no matching reader)
2011/04/18 22:02:33 2CDD7500 c user (0B01&000000/151A/67:067B): not found (121 ms) by satellitebg (of 1 avail 1)
2011/04/18 22:02:33 2CDD7500 c dvbapi: try pids again #2
2011/04/18 22:02:33 2CDD7500 c user (0D06&0000C0/151A/B4:E7D4): rejected group (121 ms) (of 0 avail 0) (no matching reader)
2011/04/18 22:02:33 2CDD7500 c user (0B01&000000/151A/67:067B): not found (121 ms) by satellitebg (of 1 avail 1)
2011/04/18 22:02:33 2CDD7500 c dvbapi: try pids again #3
2011/04/18 22:02:33 2CDD7500 c dvbapi: can't decode channel
2011/04/18 22:02:33 2CDD7500 c user (0D06&0000C0/151A/B4:E7D4): rejected group (121 ms) (of 0 avail 0) (no matching reader)
Помощ!
Мерси предварително.
Само да добавя, освен bin-a файловете които имам в /var/tuxbox/config/ са:
oscam.conf
oscam.dvbapi
oscam.server
oscam.services
oscam.srvid
oscam.user
Да не трябва още нещо?
Причината е същата, каквато е дал и @Хиена няколко мнения по-горе - картата не е обновена:
2011/04/18 22:02:31 2C5D7500 r Package: 1, id: 1010, date: 2011/04/11 - 2011/04/16, name: Preview1
Снощи им писах, те казаха че е наред. Днес им се обадих, те след около 30мин. ми звъннаха и казаха че всичко е както трябва. Не би трябвало това да е причината, въпреки че като си знам късмета...
Опитай в oscam.user да смениш реда "au=1" на "au=satellitebg".
Така е ето го:
[account]
user = user
group = 1
uniq = 0
au= satellitebg
monlevel = 4
keepalive = 1
@itzko ти не беше ли с 800, какво правят конфизите ти в /var ?
Сложи конфизите в /etc/tuxbox/config и рестартирай бокса!
@itzko - успя ли да подкараш ъпдейта на картата със oscam-a, на последък нямам много врема да го ръчкам, ако си успял би ли споделил как.
Цитат на: Хиена;95672@itzko ти не беше ли с 800, какво правят конфизите ти в /var ?
Сложи конфизите в /etc/tuxbox/config и рестартирай бокса!
Зависи от имиджа.
При ICVS -имидж от там има директна препратка.
Поздрави.
Ами аз точно съм с ICVS и конфизите ми са точно там където съм посочил!
В бина е зададено къде да ги търси.
Поздрави!
Цитат на: миронски;95790Зависи от имиджа.
При ICVS -имидж от там има директна препратка.
Поздрави.
Да ама и зависи и от бокса най вече...VAR/etc и etc/ са за некои боксове все пак.
Здравейте,
там където са конфигурационните файлове ги чете, нямаше нужда да ги местя. Като се старитра бинарито си пише че там ги търси.
@piris
тръгна след много борба, и се ъпдейтна от пусната линия към СТАРИЯ (човека си загуби два часа с мен), моя дрейм не можа да я ъпдейтне. Единствената разлика, която успях да намеря е че
[account]
user = user
group = 1
uniq = 0
au= satellitebg
monlevel = 4
keepalive = 1
при неговия account липсваше uniq = 0. Не знам дали това е помогнало или не, но така се получи.
Браво на вас, радвам се, че сте се справили с проблема.
Похвално е когато потребителите безкористно си помагат!
Цитат на: itzko;95869Здравейте,
там където са конфигурационните файлове ги чете, нямаше нужда да ги местя. Като се старитра бинарито си пише че там ги търси.
@piris
тръгна след много борба, и се ъпдейтна от пусната линия към СТАРИЯ (човека си загуби два часа с мен), моя дрейм не можа да я ъпдейтне. Единствената разлика, която успях да намеря е че
[account]
user = user
group = 1
uniq = 0
au= satellitebg
monlevel = 4
keepalive = 1
при неговия account липсваше uniq = 0. Не знам дали това е помогнало или не, но така се получи.
uniq = 0|1|2|4
unique level:
0 = disabled, default
1 = only one connection per user is allowed
2 = set user to fake if source ip is different
(e.g. for newcamd clients with different CAIDs and ports)
3 = only one connection per user, but only the last login
will survive (old mpcs behavior)
4 = set user only to fake if source ip is different,
but only the last login will survive
Цитат на: piris;94838Здравейте, взех си карта Conax на Satellitebg и не ми разкодира каналите, къде да търся проблема?
Ето лога на oscam-a:
2011/04/13 0:54:04 2AAC6850 s >> OSCam << cardserver started version 1.00-unstable_svn, build #4574 (mips-tuxbox-linux)
2011/04/13 0:54:04 2AAC6850 s version=1.00-unstable_svn, build #4574, system=mips-tuxbox-linux, nice=-1
2011/04/13 0:54:04 2AAC6850 s client max. idle=120 sec, debug level=0
2011/04/13 0:54:04 2AAC6850 s max. logsize=32 Kb
2011/04/13 0:54:04 2AAC6850 s client timeout=5000 ms, fallback timeout=2500 ms, cache delay=120 ms
2011/04/13 0:54:04 2AAC6850 s auth size=4976
2011/04/13 0:54:04 2AAC6850 s services reloaded: 0 services freed, 1 services loaded
2011/04/13 0:54:04 2AAC6850 s userdb reloaded: 1 accounts loaded, 0 expired, 0 disabled
2011/04/13 0:54:04 2AAC6850 s signal handling initialized (type=sysv)
2011/04/13 0:54:04 2AAC6850 s 37 service-id's loaded
2011/04/13 0:54:04 2AAC6850 s can't open file "/var/tuxbox/config/oscam.tiers" (err=2), no tier-id's loaded
2011/04/13 0:54:04 2AAC6850 s can't open file "/var/tuxbox/config/oscam.provid" (err=2), no provids's loaded
2011/04/13 0:54:04 2AAC6850 s can't open file "/var/tuxbox/config/oscam.ird" (errno=2) irdeto guessing not loaded
2011/04/13 0:54:04 2AAC6850 s monitor: initialized (fd=8, port=988)
2011/04/13 0:54:04 2AAC6850 s camd33: disabled
2011/04/13 0:54:04 2AAC6850 s camd35: disabled
2011/04/13 0:54:04 2AAC6850 s cs378x: disabled
2011/04/13 0:54:04 2AAC6850 s newcamd: disabled
2011/04/13 0:54:04 2AAC6850 s cccam: disabled
2011/04/13 0:54:04 2AAC6850 s radegast: disabled
2011/04/13 0:54:04 2AAC6850 s http thread started
2011/04/13 0:54:04 2AAC6850 s creating thread for device /dev/sci0
2011/04/13 0:54:04 2AAC6850 s loadbalancer: can't read from file /tmp/.oscam/stat
2011/04/13 0:54:04 2AAC6850 s waiting for local card init
2011/04/13 0:54:04 2AEFF4B0 h HTTP Server listening on port 8888
2011/04/13 0:54:04 2AFFF4B0 r reader thread started (thread=2AFFF4B0, label=satellitebg, device=/dev/sci0, detect=cd, mhz=500, cardmhz=357)
2011/04/13 0:54:04 2AFFF4B0 r satellitebg card detected
2011/04/13 0:54:05 2AFFF4B0 r ATR: 3B 34 94 00 30 42 30 30
2011/04/13 0:54:07 2AFFF4B0 r Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz
2011/04/13 0:54:08 2AFFF4B0 r type: Conax, caid: 0B01, serial: ХХХХХХХХХХ, hex serial: ХХХХХХХ, card: v64
2011/04/13 0:54:08 2AFFF4B0 r Providers: 1
2011/04/13 0:54:08 2AFFF4B0 r Provider: 1 Provider-Id: 000000
2011/04/13 0:54:08 2AFFF4B0 r Provider: 1 SharedAddress: 00000000
2011/04/13 0:54:08 2AFFF4B0 r found cardsystem
2011/04/13 0:54:08 2AFFF4B0 r Package: 1, id: 1010, date: 2011/04/04 - 2011/04/09, name: Preview1
2011/04/13 0:54:08 2AFFF4B0 r [conax-reader] ready for requests
2011/04/13 0:54:08 2AAC6850 s init for all local cards done
2011/04/13 0:54:08 2AAC6850 s anti cascading disabled
2011/04/13 0:54:08 2B0FF4B0 c plain dvbapi-client granted (user, au=satellitebg)
2011/04/13 0:54:08 2B0FF4B0 c dvbapi: reread priority file oscam.dvbapi
2011/04/13 0:54:08 2B0FF4B0 c dvbapi: 2 entries read from oscam.dvbapi
2011/04/13 0:54:12 2B0FF4B0 c dvbapi: [ADD PID 0] CAID: 0D06 ECM_PID: 0513 PROVID: 000000
2011/04/13 0:54:12 2B0FF4B0 c dvbapi: [ADD PID 1] CAID: 0B01 ECM_PID: 0522 PROVID: 000000
2011/04/13 0:54:12 2B0FF4B0 c dvbapi: new program number: 1522 (0D06:1522 unknown)
2011/04/13 0:54:12 2B0FF4B0 c dvbapi: try pids again #1
2011/04/13 0:54:12 2B0FF4B0 c user (0B01&000000/1522/67:1CAC): not found (94 ms) (of 1 avail 1)
2011/04/13 0:54:12 2B0FF4B0 c dvbapi: try pids again #2
2011/04/13 0:54:12 2B0FF4B0 c user (0B01&000000/1522/67:E401): not found (85 ms) (of 1 avail 1)
здравеите не знаех към кого да се обърна и къде да питам.имам приемник стронг срт 7335хд но не сам сигурен дали ще проработи с картите конакс на сателит бг .в момента работи с старата карта на итв .моля даите съвет
Да не пускам нова тема,някой с конакс карта и дм500,гледа ли Dorcel и как,смених няколко версии на мжкам и нюкам и не ще.В конфига на нюкама си има ред за пин код,да не трябва и някъде другаде да се променя още нещо или да работи с определена версия.С друг емулатор не съм пробвал,щото ме интересува само този.А миналия месец,като бях тест,вървеше,но сега спря.Надявам,се да има някой който да каже изобщо става ли,или да не се мъча повече.
oscam, newcs+ccccam, newcs+mgcamd
Цитат на: Хиена;98647oscam, newcs+ccccam, newcs+mgcamd
Извинявам се,май съм се изразил неправилно,аз съм точно със newcs+mgcamd,нали сървара чете картата,явно в него е проблема,затова питах има ли версия с която да работи Dorcel,или освен реда със пин код има и нещо друго.
Ами при мен работи с newcs_1.67
Освен 4-те разбъркани нули, друго специфично в конфига няма.
Постни го да видим как си го нагласил.
- (http://www.dtv-bg.com/#)
- (http://www.dtv-bg.com/#) Card Readers">
[URL="http://www.dtv-bg.com/#]-[/URL]
lower
sci
600
/dev/sci0
odd
normal
Yes
Yes
No
No
No
0000000000000000
0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
No
0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
No
yes
33000
no
no
0000
round
upper
sci
600
/dev/sci1
odd
normal
Yes
Yes
No
No
No
0000000000000000
0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
No
SCI Lower Slot
sci
368
/dev/sci0
odd
normal
Yes
Yes
No
No
No
Yes
no
30000
Yes
0000
round
20
-1
8181
yes
root
********
admin
NewCSpwd
simple
internal
all
1002
normal,init
Yes
newcs
01 02 03 04 05 06 07 08 09 10 11 12 13 14
userpasslocalhost30000onoffoff0access
Ето това ти трябва за конакса на сателитите!
Хиена,до сега си играх и не става,конфига го правя 1към1 като твоя,всичко работи без дорсел,явно нещо не е наред,ама ми писна и се отказвам,поне за сега.
Странно, обажда ли се на сателитите, да не е проблема при тях.
Работи канала, звъни и досаждай.
На коалата,със вградения рийдър ми иска пин код и работи канала,тъй че проблема не от тях,въпроса е що не мога с дм500 да го подкарам,явно аз бъркам някъде,тази вечер мисля да пробвам и с оскам,но идеята ми беше със NewCS.
Здравейте търся някой да ми ъпдейтне карта на сателайтбг
ето и линия 84.22.27.70 8888 User = ALFA Pwd = ALFA
Примера е за oscam.x86
При необходимост в слот: sci0
device = /dev/scy0
Пробвайте с този [resder] в:
oscam.server
[reader]
label = satellitebg
enable = 1
protocol = mouse
device = /dev/ttyS0
pincode = 0000
detect = cd
mhz = 357
cardmhz = 357
group = 1
emmcache = 1,3,2
!!! Пина си е пин !!!
pincode = 0000
и МНОГО ВАЖНО за ъпдейта е в :
oscam.user
[account]
user = user
pwd = password
group = 1
monlevel = 1
au = satellitebg
keepalive = 0
oscam.conf
[dvbapi]
enabled = 1
Дано съм бил полезен ? ;;650
Цитат на: satco;109814
[dvbapi]
enabled = 1
И за какво ти е това на ПС?
Примера е за ПС !
Затова уточнявам да не стават грешки ! ;;650
При ПС:
[dvbapi]
enabled = 0
или се закоментира :
#[dvbapi]
#enabled = 0
(http://streamboard.gmc.to/wiki/images/4/46/HakenGruen.png) (http://streamboard.gmc.to/wiki/index.php/Datei:HakenGruen.png) parameter is optional
DVB API enabled
Example:
enabled = 0 # disabled (default) enabled = 1 # enabled
Здравейте,
Взех си втора карта Conax на Сателит и втори приемник DM800S HD PVR Satellite HD STB, DVB-S2, Sim 2.01, Loader 76, Gemini 5.0'
Картата е активирана и работи много добре на другия ми, по прост приемник Icecrypt S3000HDCCI Satellite HD STB, DVB-S2, USB PVR, CI, Conax.
Проблема ми е, че картата не тръгва на DM800S HD. Оплаках се на продавача и той ми даде някакви инструкции – прати ми FERRARI-addons-manager_5.0_mipsel.ipk и го инсталирах чрез ТЕЛНЕТ. Чрез него качих CCcam 2.2.1, CCcam 2.3.1/OScam 1.00, CCcam 2.3.1/New CS1.67. Картата не пак не тръгна
Четох всичко по форумите. Ползвах някакви готови файлове oscam.conf, oscam.server, oscam.user. Сложих ги в папка etc/ tuxbox/ config
Признавам си, че не съм на ти с тази материя. Ако не затруднявам много – някой да ми каже какъв пътя и къде греша. Стъпка по стъпка.
Трябва да оправя този приемник до няколко дена (в рамките на 2 седмици мога да го върна) и ако не тръгне – да го върна и да го сменя с по прост такъв. Започват мачовете и ми писна да се караме с жена ми кой коя телевизия да гледа. За това са ми две карти – да има мир в къщи
Предварително Благодаря на този който ще се заеме с даване на акъл на новобранци, като мен.
Бойко Корцанов
ПП.Как се изкарва тази информация която видях в началото на форума?
Ето лога на oscam-a:
2011/04/13 0:54:04 2AAC6850 s >> OSCam << cardserver started version 1.00-unstable_svn, build #4574 (mips-tuxbox-linux)
2011/04/13 0:54:04 2AAC6850 s version=1.00-unstable_svn, build #4574, system=mips-tuxbox-linux, nice=-1
2011/04/13 0:54:04 2AAC6850 s client max. idle=120 sec, debug level=0
2011/04/13 0:54:04 2AAC6850 s max. logsize=32 Kb
2011/04/13 0:54:04 2AAC6850 s client timeout=5000 ms, fallback timeout=2500 ms, cache delay=120 ms
2011/04/13 0:54:04 2AAC6850 s auth size=4976
2011/04/13 0:54:04 2AAC6850 s services reloaded: 0 services freed, 1 services loaded
2011/04/13 0:54:04 2AAC6850 s userdb reloaded: 1 accounts loaded, 0 expired, 0 disabled
2011/04/13 0:54:04 2AAC6850 s signal handling initialized (type=sysv)
2011/04/13 0:54:04 2AAC6850 s 37 service-id's loaded
2011/04/13 0:54:04 2AAC6850 s can't open file "/var/tuxbox/config/oscam.tiers" (err=2), no tier-id's loaded
2011/04/13 0:54:04 2AAC6850 s can't open file "/var/tuxbox/config/oscam.provid" (err=2), no provids's loaded
2011/04/13 0:54:04 2AAC6850 s can't open file "/var/tuxbox/config/oscam.ird" (errno=2) irdeto guessing not loaded
2011/04/13 0:54:04 2AAC6850 s monitor: initialized (fd=8, port=988)
2011/04/13 0:54:04 2AAC6850 s camd33: disabled
2011/04/13 0:54:04 2AAC6850 s camd35: disabled
2011/04/13 0:54:04 2AAC6850 s cs378x: disabled
2011/04/13 0:54:04 2AAC6850 s newcamd: disabled
2011/04/13 0:54:04 2AAC6850 s cccam: disabled
2011/04/13 0:54:04 2AAC6850 s radegast: disabled
2011/04/13 0:54:04 2AAC6850 s http thread started
2011/04/13 0:54:04 2AAC6850 s creating thread for device /dev/sci0
2011/04/13 0:54:04 2AAC6850 s loadbalancer: can't read from file /tmp/.oscam/stat
2011/04/13 0:54:04 2AAC6850 s waiting for local card init
2011/04/13 0:54:04 2AEFF4B0 h HTTP Server listening on port 8888
2011/04/13 0:54:04 2AFFF4B0 r reader thread started (thread=2AFFF4B0, label=satellitebg, device=/dev/sci0, detect=cd, mhz=500, cardmhz=357)
2011/04/13 0:54:04 2AFFF4B0 r satellitebg card detected
2011/04/13 0:54:05 2AFFF4B0 r ATR: 3B 34 94 00 30 42 30 30
2011/04/13 0:54:07 2AFFF4B0 r Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz
2011/04/13 0:54:08 2AFFF4B0 r type: Conax, caid: 0B01, serial: ХХХХХХХХХХ, hex serial: ХХХХХХХ, card: v64
2011/04/13 0:54:08 2AFFF4B0 r Providers: 1
2011/04/13 0:54:08 2AFFF4B0 r Provider: 1 Provider-Id: 000000
2011/04/13 0:54:08 2AFFF4B0 r Provider: 1 SharedAddress: 00000000
2011/04/13 0:54:08 2AFFF4B0 r found cardsystem
2011/04/13 0:54:08 2AFFF4B0 r Package: 1, id: 1010, date: 2011/04/04 - 2011/04/09, name: Preview1
2011/04/13 0:54:08 2AFFF4B0 r [conax-reader] ready for requests
2011/04/13 0:54:08 2AAC6850 s init for all local cards done
2011/04/13 0:54:08 2AAC6850 s anti cascading disabled
2011/04/13 0:54:08 2B0FF4B0 c plain dvbapi-client granted (user, au=satellitebg)
2011/04/13 0:54:08 2B0FF4B0 c dvbapi: reread priority file oscam.dvbapi
2011/04/13 0:54:08 2B0FF4B0 c dvbapi: 2 entries read from oscam.dvbapi
2011/04/13 0:54:12 2B0FF4B0 c dvbapi: [ADD PID 0] CAID: 0D06 ECM_PID: 0513 PROVID: 000000
2011/04/13 0:54:12 2B0FF4B0 c dvbapi: [ADD PID 1] CAID: 0B01 ECM_PID: 0522 PROVID: 000000
2011/04/13 0:54:12 2B0FF4B0 c dvbapi: new program number: 1522 (0D06:1522 unknown)
2011/04/13 0:54:12 2B0FF4B0 c dvbapi: try pids again #1
2011/04/13 0:54:12 2B0FF4B0 c user (0B01&000000/1522/67:1CAC): not found (94 ms) (of 1 avail 1)
2011/04/13 0:54:12 2B0FF4B0 c dvbapi: try pids again #2
2011/04/13 0:54:12 2B0FF4B0 c user (0B01&000000/1522/67:E401): not found (85 ms) (of 1 avail 1)
Здравейте,
Имам проблем с Оскам-а, ако някой може да помогне ще съм много благодарен.
Ето ми конфигурацията:
(oscam.server)
[reader]
label = satellitebg
enable = 1
protocol = internal
device = /dev/sci0
pincode = 0000
detect = cd
mhz = 500
cardmhz = 357
group = 1
emmcache = 1,3,2
caid = 0B01
ident = 0B01:000000
services = satellitebg
fallback = 0
(oscam.user)
[account]
user = user
pwd = password
group = 1
monlevel = 1
au = satellitebg
keepalive = 0
(oscam.conf)
[global]
Nice = -10
WaitForCards = 1
PreferLocalCards = 1
saveinithistory = 1
logfile = /tmp/oscam.log
[monitor]
port = 988
nocrypt = 127.0.0.1,10.0.0.1-10.0.0.50
aulow = 120
hideclient_to = 15
monlevel = 4
appendchaninfo = 0
[webif]
httpport = 10001
httprefresh = 5
httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255
[dvbapi]
enabled = 1
boxtype = dreambox
au = 1
user = user
priority = 0B01:000000
Приемникът е ДМ500ХД, имидж iCVS-Image-dm500hd-20110324162215.nfi.
Ето Оскам лога:
-------------------------------------------------------------------------------
>> OSCam << cardserver started at Sun Sep 4 20:55:50 2011
-------------------------------------------------------------------------------
2011/09/04 20:55:50 2AAC6810 s >> OSCam << cardserver started, version 1.10rc-svn, build #5921 (mips-tuxbox-linux)
2011/09/04 20:55:50 2AAC6810 s version=1.10rc-svn, build #5921, system=mips-tuxbox-linux, nice=-10
2011/09/04 20:55:50 2AAC6810 s client max. idle=120 sec, debug level=0
2011/09/04 20:55:50 2AAC6810 s max. logsize=10 Kb, loghistorysize=4096 bytes
2011/09/04 20:55:50 2AAC6810 s client timeout=5000 ms, fallback timeout=2500 ms, cache delay=0 ms
2011/09/04 20:55:50 2AAC6810 s services reloaded: 0 services freed, 0 services loaded, rejected 0
2011/09/04 20:55:50 2AAC6810 s userdb reloaded: 1 accounts loaded, 0 expired, 0 disabled
2011/09/04 20:55:50 2AAC6810 s signal handling initialized (type=sysv)
2011/09/04 20:55:50 2AAC6810 s 49 service-id's loaded in 1ms
2011/09/04 20:55:50 2AAC6810 s can't open file "/var/tuxbox/config/oscam.tiers" (err=2 No such file or directory), no tier-id's loaded
2011/09/04 20:55:50 2AAC6810 s can't open file "/var/tuxbox/config/oscam.provid" (err=2 No such file or directory), no provids's loaded
2011/09/04 20:55:50 2AAC6810 s can't open file "/var/tuxbox/config/oscam.ird" (errno=2 No such file or directory) irdeto guessing not loaded
2011/09/04 20:55:50 2AAC6810 s monitor: initialized (fd=7, port=988)
2011/09/04 20:55:50 2AAC6810 s camd33: disabled
2011/09/04 20:55:50 2AAC6810 s camd35: disabled
2011/09/04 20:55:50 2AAC6810 s cs378x: disabled
2011/09/04 20:55:50 2AAC6810 s newcamd: disabled
2011/09/04 20:55:50 2AAC6810 s radegast: disabled
2011/09/04 20:55:50 2AAC6810 s http thread started
2011/09/04 20:55:50 2AAC6810 s creating thread for device /dev/sci0
2011/09/04 20:55:50 2AAC6810 s loadbalancer: can't read from file /tmp/.oscam/stat
2011/09/04 20:55:50 2AAC6810 s waiting for local card init
2011/09/04 20:55:50 2C6094B0 r reader thread started (thread=2C6094B0, label=satellitebg, device=/dev/sci0, detect=cd, mhz=500, cardmhz=357)
2011/09/04 20:55:50 2BE094B0 h HTTP Server listening on port 10001
2011/09/04 20:55:50 2C6094B0 r satellitebg card detected
2011/09/04 20:55:51 2C6094B0 r ERROR: 0 characters found in ATR
Пробвах различни конфигурации и имиджи (заводския и openpli-1.0-dm500hd-20100912.nfi), нулев успех. При заводския ми даваше друга грешка, че не може да отвори рийдъра. От лога виждам, че проблемът е в рийдъра, но не намерих нищо в Гугъл, което да ме подсети къде бъркам.
Цитатmhz = 500
cardmhz = 357
Това го направи така
mhz = 368
cardmhz = 368
Поздрави.
Благодаря ти, че писа.
Пробвах, съобщението остава същото:
2011/09/04 21:51:02 2AAC6810 s creating thread for device /dev/sci0
2011/09/04 21:51:02 2AAC6810 s loadbalancer: can't read from file /tmp/.oscam/stat
2011/09/04 21:51:02 2AAC6810 s waiting for local card init
2011/09/04 21:51:02 2BE094B0 h HTTP Server listening on port 10001
2011/09/04 21:51:02 2C6094B0 r reader thread started (thread=2C6094B0, label=satellitebg, device=/dev/sci0, detect=cd, mhz=368, cardmhz=368)
2011/09/04 21:51:02 2C6094B0 r satellitebg card detected
2011/09/04 21:51:04 2C6094B0 r ERROR: 0 characters found in ATR
root@dm500hd:~#
Провери да няма някой друг кам стартиран, който да заема четеца.
За да провериш напиши ps в конзолата, и ще ти изкара всичко стартирано.
Прегледах процесите, ето лога:
root@dm500hd:~# ps
PID USER VSZ STAT COMMAND
1 root 1724 S init [3]
2 root 0 SW [migration/0]
3 root 0 SWN [ksoftirqd/0]
4 root 0 SW [migration/1]
5 root 0 SWN [ksoftirqd/1]
6 root 0 SW< [events/0]
7 root 0 SW< [events/1]
8 root 0 SW< [khelper]
9 root 0 SW< [kthread]
10 root 0 SW< [kblockd/0]
11 root 0 SW< [kblockd/1]
12 root 0 SW< [khubd]
13 root 0 SW [pdflush]
14 root 0 SW [pdflush]
15 root 0 SW< [kswapd0]
16 root 0 SW< [aio/0]
17 root 0 SW< [aio/1]
18 root 0 SW< [ata/0]
19 root 0 SW< [ata/1]
20 root 0 SW< [ata_aux]
21 root 0 SW< [scsi_eh_0]
22 root 0 SW< [scsi_eh_1]
23 root 0 SW [mtdblockd]
24 root 0 SWN [jffs2_gcd_mtd3]
70 root 2180 S < udevd --daemon
263 root 0 SW [kcdfsd]
316 root 0 SW [b_event]
317 root 0 SW [b_idle]
322 root 0 SW< [fp]
337 root 0 SW< [mpeg]
345 root 0 SW< [dmx0]
352 root 0 SW< [dmx1]
359 root 0 SW< [dmx2]
361 root 0 SW< [dmx3]
362 root 0 SW< [dmx4]
363 root 0 SW< [dmx_hw_sec]
406 root 1928 S /usr/bin/wdog tpmd
407 root 4312 S tpmd
440 root 4076 S nmbd -D
442 root 6780 S smbd -D
460 root 6780 S smbd -D
476 root 2520 S udhcpc -R -b -T3 -A10 -p /var/run/udhcpc.eth0.pid -i
502 messageb 2408 S /usr/bin/dbus-daemon --system
523 root 11856 S /usr/bin/gdaemon
529 root 11856 S /usr/bin/gdaemon
532 root 2348 S /usr/sbin/dropbear -r /etc/dropbear/dropbear_rsa_host
550 root 1832 S /usr/sbin/inetd
554 root 2520 S /sbin/syslogd -n -O /var/log/messages -s 32 -b 1 -m 2
556 root 2520 S /sbin/klogd -n
671 root 2256 S /usr/sbin/automount --pid-file=/var/run/autofs/_autof
729 avahi 3084 S avahi-daemon: running [dm500hd.local]
739 root 2520 S /bin/sh /usr/bin/enigma2.sh
742 root 100m S /usr/bin/enigma2
754 root 100m S /usr/bin/enigma2
768 root 100m S N /usr/bin/enigma2
769 root 100m S N /usr/bin/enigma2
773 root 100m S /usr/bin/enigma2
783 root 100m S N /usr/bin/enigma2
776 root 0 SW< [kdvb-ad-0-fe-0]
820 root 0 SW< [cifsoplockd]
821 root 0 SW< [cifsdnotifyd]
822 root 0 SW [cifsd]
909 root 2840 S telnetd
910 root 2836 S -sh
913 root 2836 R ps
Ами не се вижда друг кам, освен да пробваш с друга версия на оскама.
Пробвах няколко версии от http://download.oscam.to/index.php?&direction=0&order=mod&directory=mips-tuxbox.
Дава ми винаги грешка Segmentation fault.
Само със oscam-stable-1.10-mips-tuxbox-webif не дава тази грешка (с него е лога от по-горе).
Проблемът с подкарването на Оскам е решен, картата я бях сложил наобратно...
Каналите не се разкодират и проблемът в момента е следният:
2011/09/05 16:35:52 2AAC6810 s can't open file "/var/tuxbox/config/oscam.tiers" (err=2 No such file or directory), no tier-id's loaded
2011/09/05 16:35:52 2AAC6810 s can't open file "/var/tuxbox/config/oscam.provid" (err=2 No such file or directory), no provids's loaded
2011/09/05 16:35:52 2AAC6810 s can't open file "/var/tuxbox/config/oscam.ird" (errno=2 No such file or directory) irdeto guessing not loaded
2011/09/05 16:35:52 2AAC6810 s monitor: disabled
2011/09/05 16:35:52 2AAC6810 s camd33: disabled
2011/09/05 16:35:52 2AAC6810 s camd35: disabled
2011/09/05 16:35:52 2AAC6810 s cs378x: disabled
2011/09/05 16:35:52 2AAC6810 s newcamd: disabled
2011/09/05 16:35:52 2AAC6810 s radegast: disabled
2011/09/05 16:35:52 2AAC6810 s http thread started
2011/09/05 16:35:52 2AAC6810 s creating thread for device /dev/sci0
2011/09/05 16:35:52 2AAC6810 s loadbalancer: can't read from file /tmp/.oscam/stat
2011/09/05 16:35:52 2AAC6810 s waiting for local card init
2011/09/05 16:35:52 2BE094B0 h HTTP Server listening on port 10001
2011/09/05 16:35:52 2C6094B0 r reader thread started (thread=2C6094B0, label=satellitebg, device=/dev/sci0, detect=cd, mhz=357, cardmhz=357)
2011/09/05 16:35:52 2C6094B0 r satellitebg card detected
2011/09/05 16:35:54 2C6094B0 r ATR: 3B 34 94 00 30 42 30 30
2011/09/05 16:35:56 2C6094B0 r Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz
2011/09/05 16:35:57 2C6094B0 r type: Conax, caid: 0B01, serial: 2033007088, hex serial: 792d39f0, card: v64
2011/09/05 16:35:57 2C6094B0 r Providers: 1
2011/09/05 16:35:57 2C6094B0 r Provider: 1 Provider-Id: 000000
2011/09/05 16:35:57 2C6094B0 r Provider: 1 SharedAddress: 00000000
2011/09/05 16:35:57 2C6094B0 r found cardsystem conax
2011/09/05 16:35:57 2C6094B0 r Package: 1, id: 1010, classes: 010FFFFF, date: 2011/08/19 - 2011/08/24, name: Preview1
2011/09/05 16:35:57 2C6094B0 r Package: 2, id: 1010, classes: 010FFFFF, date: 1990/01/01 - 1990/01/01, name: Preview1
2011/09/05 16:35:57 2C6094B0 r [conax-reader] ready for requests
2011/09/05 16:35:57 2AAC6810 s init for all local cards done
2011/09/05 16:35:57 2AAC6810 s anti cascading disabled
2011/09/05 16:35:57 2D6194B0 c plain dvbapi-client granted (dummy, au=on (1 reader))
2011/09/05 16:35:57 2D6194B0 c dvbapi: can't open priority file /var/tuxbox/config/oscam.dvbapi
2011/09/05 16:35:59 2D6194B0 c dvbapi: [ADD PID 0] CAID: 0B01 ECM_PID: 01FA PROVID: 000000
2011/09/05 16:35:59 2D6194B0 c dvbapi: [ADD PID 1] CAID: 0D06 ECM_PID: 01F9 PROVID: 000000
2011/09/05 16:35:59 2D6194B0 c dvbapi: new program number: 157F (BNT1\)
2011/09/05 16:35:59 2C6094B0 r Error processing ecm for caid 0B01, srvid 157F (servicename: BNT1\) on reader satellitebg.
2011/09/05 16:35:59 2D6194B0 c dummy (0B01&000000/157F/67:7376): not found (99 ms) by satellitebg (of 1 avail 1)
2011/09/05 16:36:00 2D6194B0 c dvbapi: try pids again #1
2011/09/05 16:36:00 2D6194B0 c dummy (0D06&0000C0/157F/B4:B779): rejected group (0 ms) (of 0 avail 0) (no matching reader)
2011/09/05 16:36:00 2D6194B0 c dummy (0B01&000000/157F/67:7376): not found (0 ms) by satellitebg (of 1 avail 1)
2011/09/05 16:36:00 2D6194B0 c dvbapi: try pids again #2
2011/09/05 16:36:00 2D6194B0 c dummy (0D06&0000C0/157F/B4:B779): rejected group (0 ms) (of 0 avail 0) (no matching reader)
2011/09/05 16:36:00 2D6194B0 c dummy (0B01&000000/157F/67:7376): not found (0 ms) by satellitebg (of 1 avail 1)
2011/09/05 16:36:00 2D6194B0 c dvbapi: try pids again #3
2011/09/05 16:36:00 2D6194B0 c dvbapi: can't decode channel
2011/09/05 16:36:00 2D6194B0 c dummy (0D06&0000C0/157F/B4:B779): rejected group (0 ms) (of 0 avail 0) (no matching reader)
В статуса на картата пише CARDOK (no entitlements).
Конфигурацията ми е следната:
Оскам.конф
[global]
Nice = -1
WaitForCards = 1
PreferLocalCards = 1
saveinithistory = 1
logfile = /tmp/oscam.log
[webif]
httpport = 10001
httprefresh = 5
httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255
[dvbapi]
enabled = 1
boxtype =
au = 1
user = dummy
Оскам.сървър
[reader]
label = satellitebg
enable = 1
protocol = internal
device = /dev/sci0
pincode = 0000
detect = cd
group = 1
emmcache = 1,3,2
Оскам.усер
[account]
user = dummy
pwd = dummy
group = 1
monlevel = 1
au = satellitebg
Изчетох темата, явно картата трябва да се ъпне.
Ще звъня на съпорта.
Може ли да стане директно през Оскам?
На Булсата трябва да стои на Канал 1, може би има такъв канал и на Сателайта?
Превключи на Нова Телевизия и не пипай до сутринта.
Превключих и ще чакам. Трябва ли да рестартирам Оскама или всичко ще тръгне самичко?
Това с изчакването е малко странно...
Влезни в WEB на оско...
Това ако не е така не ще се ъпне никога...
Рестарта след всякакви промени е задължителен, освен ако не са правени някои промени през WEB...
В уеба на Оскама наистина показва
2011/09/05 19:59:02 2C6094B0 r Package: 1, id: 1010, classes: 010FFFFF, date: 2011/08/19 - 2011/08/24, name: Preview1
2011/09/05 19:59:02 2C6094B0 r Package: 2, id: 1010, classes: 010FFFFF, date: 1990/01/01 - 1990/01/01, name: Preview1
Картата съм я взел на 19 август и вероятно затова датите са така.
Звъннах на съпорта, от там ме посъветваха да оставя приемника за половин-един час на транспондера на Канал 1 (12051). Момчето обаче не беше наясно дали може да стане директно през Оскама, та ще видя утре сутринта.
Става директно през оскам за секунди, но трябва да ти показва активен ау-то.
Картата се ъпва почти на момента,ако е платено всичко и оскам е конфигуриран правилно.
Другия вариант е да пуснеш N линия на някой с mgcamd да тия ъпне.
Докато не се ъпне няма да покаже актуална дата...;;650
Добре, сложих си и мгкамд. Вързал съм го, ударете едно рамо, имам чувството, че съм накрая на баира :). В лога на мгкамд ми излиза следното:
got 8 cmd 9F
got 51 cmd 9F
[mg0] namespace EB0000 t-id C92 on-id 3
[mg0] descramble on 1, source 0
[mg0] service 1589 index 0 pmt pid 74 (3), pids: video 0x00D8, audio 0x013C
[mg0] ECM: CaID: 0x0B01 -> CaPID: 0x0216 ProvID: 000000
[mg0] ECM: CaID: 0x0D06 -> CaPID: 0x0215 ProvID: 000000
ECM: -- Tue Sep 6 22:07:55 2011
----------------------------------------------------
000: 80 70 64 70 62 64 20 49 b0 37 b2 1f 03 ab 94 70 .pdpbd I.7.....p
010: 8b 1f 59 10 ce 3a 82 f8 ab 11 09 36 af 37 86 e2 ..Y..:.....6.7..
020: df d5 b4 ae 21 05 11 e4 0f c9 6e 89 77 87 c7 cc ....!.....n.w...
030: 55 28 66 81 d9 8b 1c 9c ef 73 29 54 0e 9c 08 9e U(f......s)T....
040: e6 d6 ae d9 5b de f2 69 17 1f 0c 01 43 8a 3f 4f ....[..i....C.?O
050: e8 28 50 ec f5 48 6e 7e 9e da 40 f0 1d 73 18 ad .(P..Hn...@..s..
060: c7 51 27 38 a2 9a 80 .Q'8...
[mg0] No conax key(s) found for id 0 keynr 20
[mg0] -> ECM to newcamd 127.0.0.1:34000
[mg0] newcamd route 127.0.0.1:34000 cant decode (15ms)
[mg0] network can't decode
[mg0] pid 0x0216 failed to decode.
ECM: -- Tue Sep 6 22:07:57 2011
----------------------------------------------------
000: 81 70 b1 81 ff 28 00 ac 80 60 f3 20 c8 db 95 d3 .p...(...`. ....
010: 57 5d 66 0c cf 28 29 fa 46 e8 a9 66 45 07 ac cc W]f..().F..fE...
020: 7a a9 68 d3 0e 33 f2 5f 62 b1 6e 8b 86 45 e6 2e z.h..3._b.n..E..
030: 10 e3 40 b0 f6 e2 23 c2 7d 99 64 04 8c c0 a7 a5 ..@...#...d.....
040: 1b 5f 88 1c ae 05 8d 34 fd 22 1a db 77 6a ae be ._.....4."..wj..
050: 7e 5d d7 75 8c df 7f f6 11 c5 32 73 a8 03 da 4b .].u......2s...K
060: 26 d8 3d 55 88 c8 b1 e7 ed b1 83 01 c1 84 02 c1 &.=U............
070: 01 85 29 81 0d 83 af 46 4a be 18 ed aa 8d 50 e5 ..)....FJ.....P.
080: 91 d5 58 32 38 aa eb dc 1d 2b eb 42 c5 31 ba 7a ..X28....+.B.1.z
090: d8 6f 63 38 e2 c3 b4 53 61 ba c8 01 86 08 4b e0 .oc8...Sa.....K.
0A0: 0b 02 dd c4 73 34 8e 02 2b 26 df 08 1d 9f 99 c5 ....s4..+&......
0B0: bc 78 f7 32 .x.2
no cryptoworks RSA found
no cryptoworks RSA found
[mgcamd] Cryptoworks key(s) not found for caid 0D06 provid c0 keynr 01
[mg0] network can't decode
[mg0] pid 0x0215 failed to decode.
[mgcamd] emm started
EMM: CaID: 0x0D06 -> CaPID: 0x0021 ProvID: 000000
Starting emm for newcamd shared card
*EMM: CaID: 0x0B01 -> CaPID: 0x0024 ProvID: 000000
ECM: -- Tue Sep 6 22:07:58 2011
----------------------------------------------------
000: 80 70 64 70 62 64 20 49 b0 37 b2 1f 03 ab 94 70 .pdpbd I.7.....p
010: 8b 1f 59 10 ce 3a 82 f8 ab 11 09 36 af 37 86 e2 ..Y..:.....6.7..
020: df d5 b4 ae 21 05 11 e4 0f c9 6e 89 77 87 c7 cc ....!.....n.w...
030: 55 28 66 81 d9 8b 1c 9c ef 73 29 54 0e 9c 08 9e U(f......s)T....
040: e6 d6 ae d9 5b de f2 69 17 1f 0c 01 43 8a 3f 4f ....[..i....C.?O
050: e8 28 50 ec f5 48 6e 7e 9e da 40 f0 1d 73 18 ad .(P..Hn...@..s..
060: c7 51 27 38 a2 9a 80 .Q'8...
[mg0] -> ECM to newcamd 127.0.0.1:34000
[mg0] newcamd route 127.0.0.1:34000 cant decode (15ms)
ECM: -- Tue Sep 6 22:07:58 2011
----------------------------------------------------
000: 81 70 b1 81 ff 28 00 ac 80 60 f3 20 c8 db 95 d3 .p...(...`. ....
010: 57 5d 66 0c cf 28 29 fa 46 e8 a9 66 45 07 ac cc W]f..().F..fE...
020: 7a a9 68 d3 0e 33 f2 5f 62 b1 6e 8b 86 45 e6 2e z.h..3._b.n..E..
030: 10 e3 40 b0 f6 e2 23 c2 7d 99 64 04 8c c0 a7 a5 ..@...#...d.....
040: 1b 5f 88 1c ae 05 8d 34 fd 22 1a db 77 6a ae be ._.....4."..wj..
050: 7e 5d d7 75 8c df 7f f6 11 c5 32 73 a8 03 da 4b .].u......2s...K
060: 26 d8 3d 55 88 c8 b1 e7 ed b1 83 01 c1 84 02 c1 &.=U............
070: 01 85 29 81 0d 83 af 46 4a be 18 ed aa 8d 50 e5 ..)....FJ.....P.
080: 91 d5 58 32 38 aa eb dc 1d 2b eb 42 c5 31 ba 7a ..X28....+.B.1.z
090: d8 6f 63 38 e2 c3 b4 53 61 ba c8 01 86 08 4b e0 .oc8...Sa.....K.
0A0: 0b 02 dd c4 73 34 8e 02 2b 26 df 08 1d 9f 99 c5 ....s4..+&......
0B0: bc 78 f7 32 .x.2
no cryptoworks RSA found
no cryptoworks RSA found
[mgcamd] Cryptoworks key(s) not found for caid 0D06 provid c0 keynr 01
ECM: -- Tue Sep 6 22:07:59 2011
(newcamd.list)
CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS = 127.0.0.1 34000 User1Username User1Password 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
(oscam.conf)
[newcamd]
port = 34000@0B01:000000
key = 0102030405060708091011121314
mgclient = 1
(oscam.user)
[account]
user = User1Username
pwd = User1Password
group = 2
monlevel = 0
au = satellitebg
(mg_cfg)
# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }
# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 02 }
# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 01 }
# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0
# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 01 }
# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30
# network ecm timeout in seconds
K: { 05 }
# newcamd dead routes connect retry, sec
Q: { 600 }
# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password
# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80
# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 02 } 172.16.1.1 28007 /tmp/mgcamd.log
# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }
# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }
# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 04 }
# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }
# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 00 }
# map all 180x nagra caids to 1801
# default is 01
F: { 00 }
Цитат на: тотален;117848Добре, сложих си и мгкамд. Вързал съм го, ударете едно рамо, имам чувството, че съм накрая на баира :). В лога на мгкамд ми излиза следното:
got 8 cmd 9F
got 51 cmd 9F
[mg0] namespace EB0000 t-id C92 on-id 3
[mg0] descramble on 1, source 0
[mg0] service 1589 index 0 pmt pid 74 (3), pids: video 0x00D8, audio 0x013C
[mg0] ECM: CaID: 0x0B01 -> CaPID: 0x0216 ProvID: 000000
[mg0] ECM: CaID: 0x0D06 -> CaPID: 0x0215 ProvID: 000000
ECM: -- Tue Sep 6 22:07:55 2011
----------------------------------------------------
000: 80 70 64 70 62 64 20 49 b0 37 b2 1f 03 ab 94 70 .pdpbd I.7.....p
010: 8b 1f 59 10 ce 3a 82 f8 ab 11 09 36 af 37 86 e2 ..Y..:.....6.7..
020: df d5 b4 ae 21 05 11 e4 0f c9 6e 89 77 87 c7 cc ....!.....n.w...
030: 55 28 66 81 d9 8b 1c 9c ef 73 29 54 0e 9c 08 9e U(f......s)T....
040: e6 d6 ae d9 5b de f2 69 17 1f 0c 01 43 8a 3f 4f ....[..i....C.?O
050: e8 28 50 ec f5 48 6e 7e 9e da 40 f0 1d 73 18 ad .(P..Hn...@..s..
060: c7 51 27 38 a2 9a 80 .Q'8...
[mg0] No conax key(s) found for id 0 keynr 20
[mg0] -> ECM to newcamd 127.0.0.1:34000
[mg0] newcamd route 127.0.0.1:34000 cant decode (15ms)
[mg0] network can't decode
[mg0] pid 0x0216 failed to decode.
ECM: -- Tue Sep 6 22:07:57 2011
----------------------------------------------------
000: 81 70 b1 81 ff 28 00 ac 80 60 f3 20 c8 db 95 d3 .p...(...`. ....
010: 57 5d 66 0c cf 28 29 fa 46 e8 a9 66 45 07 ac cc W]f..().F..fE...
020: 7a a9 68 d3 0e 33 f2 5f 62 b1 6e 8b 86 45 e6 2e z.h..3._b.n..E..
030: 10 e3 40 b0 f6 e2 23 c2 7d 99 64 04 8c c0 a7 a5 ..@...#...d.....
040: 1b 5f 88 1c ae 05 8d 34 fd 22 1a db 77 6a ae be ._.....4."..wj..
050: 7e 5d d7 75 8c df 7f f6 11 c5 32 73 a8 03 da 4b .].u......2s...K
060: 26 d8 3d 55 88 c8 b1 e7 ed b1 83 01 c1 84 02 c1 &.=U............
070: 01 85 29 81 0d 83 af 46 4a be 18 ed aa 8d 50 e5 ..)....FJ.....P.
080: 91 d5 58 32 38 aa eb dc 1d 2b eb 42 c5 31 ba 7a ..X28....+.B.1.z
090: d8 6f 63 38 e2 c3 b4 53 61 ba c8 01 86 08 4b e0 .oc8...Sa.....K.
0A0: 0b 02 dd c4 73 34 8e 02 2b 26 df 08 1d 9f 99 c5 ....s4..+&......
0B0: bc 78 f7 32 .x.2
no cryptoworks RSA found
no cryptoworks RSA found
[mgcamd] Cryptoworks key(s) not found for caid 0D06 provid c0 keynr 01
[mg0] network can't decode
[mg0] pid 0x0215 failed to decode.
[mgcamd] emm started
EMM: CaID: 0x0D06 -> CaPID: 0x0021 ProvID: 000000
Starting emm for newcamd shared card
*EMM: CaID: 0x0B01 -> CaPID: 0x0024 ProvID: 000000
ECM: -- Tue Sep 6 22:07:58 2011
----------------------------------------------------
000: 80 70 64 70 62 64 20 49 b0 37 b2 1f 03 ab 94 70 .pdpbd I.7.....p
010: 8b 1f 59 10 ce 3a 82 f8 ab 11 09 36 af 37 86 e2 ..Y..:.....6.7..
020: df d5 b4 ae 21 05 11 e4 0f c9 6e 89 77 87 c7 cc ....!.....n.w...
030: 55 28 66 81 d9 8b 1c 9c ef 73 29 54 0e 9c 08 9e U(f......s)T....
040: e6 d6 ae d9 5b de f2 69 17 1f 0c 01 43 8a 3f 4f ....[..i....C.?O
050: e8 28 50 ec f5 48 6e 7e 9e da 40 f0 1d 73 18 ad .(P..Hn...@..s..
060: c7 51 27 38 a2 9a 80 .Q'8...
[mg0] -> ECM to newcamd 127.0.0.1:34000
[mg0] newcamd route 127.0.0.1:34000 cant decode (15ms)
ECM: -- Tue Sep 6 22:07:58 2011
----------------------------------------------------
000: 81 70 b1 81 ff 28 00 ac 80 60 f3 20 c8 db 95 d3 .p...(...`. ....
010: 57 5d 66 0c cf 28 29 fa 46 e8 a9 66 45 07 ac cc W]f..().F..fE...
020: 7a a9 68 d3 0e 33 f2 5f 62 b1 6e 8b 86 45 e6 2e z.h..3._b.n..E..
030: 10 e3 40 b0 f6 e2 23 c2 7d 99 64 04 8c c0 a7 a5 ..@...#...d.....
040: 1b 5f 88 1c ae 05 8d 34 fd 22 1a db 77 6a ae be ._.....4."..wj..
050: 7e 5d d7 75 8c df 7f f6 11 c5 32 73 a8 03 da 4b .].u......2s...K
060: 26 d8 3d 55 88 c8 b1 e7 ed b1 83 01 c1 84 02 c1 &.=U............
070: 01 85 29 81 0d 83 af 46 4a be 18 ed aa 8d 50 e5 ..)....FJ.....P.
080: 91 d5 58 32 38 aa eb dc 1d 2b eb 42 c5 31 ba 7a ..X28....+.B.1.z
090: d8 6f 63 38 e2 c3 b4 53 61 ba c8 01 86 08 4b e0 .oc8...Sa.....K.
0A0: 0b 02 dd c4 73 34 8e 02 2b 26 df 08 1d 9f 99 c5 ....s4..+&......
0B0: bc 78 f7 32 .x.2
no cryptoworks RSA found
no cryptoworks RSA found
[mgcamd] Cryptoworks key(s) not found for caid 0D06 provid c0 keynr 01
ECM: -- Tue Sep 6 22:07:59 2011
(newcamd.list)
CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS = 127.0.0.1 34000 User1Username User1Password 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
(oscam.conf)
[newcamd]
port = 34000@0B01:000000
key = 0102030405060708091011121314
mgclient = 1
(oscam.user)
[account]
user = User1Username
pwd = User1Password
group = 2
monlevel = 0
au = satellitebg
(mg_cfg)
# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }
# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 02 }
# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 01 }
# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0
# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 01 }
# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30
# network ecm timeout in seconds
K: { 05 }
# newcamd dead routes connect retry, sec
Q: { 600 }
# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password
# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80
# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 02 } 172.16.1.1 28007 /tmp/mgcamd.log
# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }
# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }
# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 04 }
# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }
# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 00 }
# map all 180x nagra caids to 1801
# default is 01
F: { 00 }
Колега не разбирам много но виждам че оскам конфиг не ти е пълен.Виж в стримборда какви са задължителните настроики за оскам. Нямаш и фаил оскам сървар където се описват ридарите , виждам че нищо не ти чете картата.Ако искаш мога да ти дам основните конфизи с които работи и оттам нататък ги преправи. Наи лесно е през уебинфото на оскам там се вижда всичко.
Малко по надоло в темата има писано за оскам прочети го.
http://www.dtv-bg.com/showthread.php?t=17284
Само за пробата и за ъпдейта да си качи нюцс с клиент мгкамд. Ъп-а става за 0 време.
Боби, ти направо тотално го обърка ;;573
oscam.conf
[global]
logfile = stdout
cwlogdir = /tmp/cw
fallbacktimeout = 1600
cachedelay = 120
unlockparental = 1
nice = -1
maxlogsize = 200
preferlocalcards = 1
saveinithistory = 1
dropdups = 1
lb_mode = 1
lb_save = 100
[monitor]
hideclient_to = 15
appendchaninfo = 0
[dvbapi]
enabled = 1
au = 1
boxtype = dreambox
user = dvbapi
pmt_mode = 0
request_mode = 0
[webif]
httpport = 12345
httpuser = root
httppwd = dreambox
httprefresh = 10
httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255
oscam.dvbapi
P: 0B01:000000
oscam.server
[reader]
label = satbg
enable = 1
protocol = internal
device = /dev/sci0
pincode = 0000
caid = 0B01
detect = cd
ident = 0B01:000000
group = 1
emmcache = 1,3,2
ecmcache = 1
lb_weight = 100
oscam.user
[account]
user = dvbapi
pwd = password
group = 1
uniq = 2
monlevel = 1
au = satbg
Рестарт на оскам и огън....
Мерси много.
Сутринта успях да ъпдейтна картата с оскам и мгкамд.
Бая зор видях, но тръгна, пък и понаучих как се конфигурират нещата.
Цитат на: тотален;117697Проблемът с подкарването на Оскам е решен, картата я бях сложил наобратно...
Ти си за пребиване ;;650
Цитат на: Момчил Минков;117990Ти си за пребиване ;;650
Чак пък пребиване - дърпане на ушенце има същия педагогически ефект :).
На картата има стрелка в коя посока да се слага и от двете страни, не е трудно да се обърка.
Цитат на: тотален;118074На картата има стрелка в коя посока да се слага и от двете страни, не е трудно да се обърка.
Приемника има книжка, там е показано от коя страна трябва да е чипа при поставяне на картата ;)