The Best Streaming Software!
VIVO Rent A Car - Your car rental
Върни се   Digital TV Forums - БЪЛГАРСКИЯТ ФОРУМ ЗА ЦИФРОВА ТЕЛЕВИЗИЯ > ДИСКУСИИ - Всичко за сателитната и наземната телевизия > КОНВЕРТОРИ

КОНВЕРТОРИ Фланцови, офсетови, c-band конвертори, пластини, облъчватели, държачи, мултифиид-рейки.

Отговори
 
Контрол над темата Търси в тази тема Начин на разглеждане
  #1  
Стар 26-06-2009
Аватара на ТИНТИН
ТИНТИН ТИНТИН не е на линия
Модератор
 

Дата на присъединяване: Mar 2009
Мнения: 4,148
Благодари: 362
Получил благодарност:
2,431 пъти в 1,521 поста
Сваляния: 71
Ъплоуди: 0
По подразбиране How DiSEqC Works

DiSEqC is an open standard that stands for Digital Satellite Equipment Control. Why DiSEqC


In order to squeeze more channels into a given frequency band width, channels are transmitted with vertical OR horizontal polarisation.

The conventional LNB known as the "Marconi (polarisation) Switching LNB" responds to the supply voltage to change the polarisation. If the supply voltage going up the dish cable is less than 15 volts, the LNB will "see" only vertically polarised transmissions. If the voltage is more than 15 volts, it will "see" only horizontally polarised transmissions.

The older type of LNB had a separate polariser to do this job and was able to use the voltage to select High Band or Low Band operation (by changing the internal oscillator frequency).

So the modern LNB has a problem if it has to switch between two frequency bands. The problem was overcome with the introduction of the "Universal" LNB.

The "Universal" LNB switches polarisation with voltage but it also switches its internal oscillator for "High Band" when it "hears" a 22kHz tone. Specificallly, the oscillator changes from 9.75 GHz to 10.6 GHz.

Recently manufactured receivers incorporate a 22kHz tone generator which is menu-selectable on a per-channel basis. (One exception is the Ferguson SRD6 which has a tone generator but no menu selection. The tone comes on automatically if you program a channel for a higher frequency).

Older receivers require an external tone generator box in order to make the "Universal" LNB select High Band. The external box can be controlled by a manually operated switch or by some feature of the receiver which will put a voltage onto its control wire to switch it on.

An alternative use for the 22kHz tone is to control an external switching box whichfeeds signals from one of a pair of LNBs into the receiver. For example, you could have two separate LNBs on a dish connected to a switching box which is itself connected to the receiver by a single coaxial cable. When the box "hears" a 22kHz tone it swaps to the other LNB.

DiSEqC is an extension of this idea. It relies on a switching box which detects the 22kHz tone pulsing rapidly on and off. In this way, a specially designed receiver can control numerous LNBs through a DiSEqC switching box.

How DiSEqC Works


DiSEqC messages are sent as sequences of short bursts of 22KHz tone modulated on the LNB power supply carried by the coax cable from the LNB input on the receiver (the master). Messages comprise a number of digital bytes of eight bits each. Each bit occupies a specific time and teh proportion of that time filled with the 22KHz burst determines whether that bit is a 1 or a 0.

The first byte is the Framing byte. The first five bits in this follow the pattern, '11100' to allow listening devices (slaves) to synchronise to the signal. Some of these may change with later versions of DiSEqC. The sixth bit is set to 0 if the message is a command from the master or 1 if it's a reply from a slave. Bit seven is set to '1' if a response is required or 0 if not. The last framing bit signals whether this message is a re-transmission of a message for which a reply has not been received.

The second byte indicates which family of devices the message is for. The first half (four bits) indicates the type of device (LNB, switch, positioner etc) and the second half the particular type. In each half of this Address byte a value of 0 means the message is open to all.

Next comes the Command byte. This actually tells the listening devices what to do. This is followed by a number of Data bytes to pass on numbers relevant to the command (such as the angle required from a separate polariser).

For control of simple mini-DiSEqC switches, one of two tone bursts, generated with a sequence of nine DiSEqC '1' bits and a 12.5ms burst of 'raw' 22KHz tone.
DiSEqC Applications


DiSEqC system has been designed primarily to meet the problem of two-satellite, two-band systems with ease. It has dedicated outputs to select polarity, satellite position and frequency band.
Прикрепени изображения
Тип файл: jpg DiSEqC.jpg (7.6 КБ, 94 разглеждания)
Отговори с цитат
Следните потребители (5) благодарят на ТИНТИН за този полезен пост
hajduk (09-07-2009), mr321 (30-06-2009), netman (08-08-2009), thunderstorm6 (13-07-2009), Ники (27-06-2009)
  #2  
Стар 09-07-2009
Аватара на Ooo_Pepi
Ooo_Pepi Ooo_Pepi не е на линия
върл SAT фен
 

Дата на присъединяване: Jul 2009
Местоположение: София
Мнения: 3,342
Благодари: 2,625
Получил благодарност:
1,742 пъти в 886 поста
Сваляния: 5
Ъплоуди: 1
По подразбиране

Много хубаво, ако някой се навие да го преведе ще бъде прекрасно. 10х
Отговори с цитат
  #3  
Стар 09-07-2009
Аватара на ТИНТИН
ТИНТИН ТИНТИН не е на линия
Модератор
 

Дата на присъединяване: Mar 2009
Мнения: 4,148
Благодари: 362
Получил благодарност:
2,431 пъти в 1,521 поста
Сваляния: 71
Ъплоуди: 0
По подразбиране

Още малко по темата....

DiSEqC
Digital Satellite Equipment Control - developed vby EUTELSAT and Phillips. The purpose was to define a standard enabling satellite recievers to control aad-on equipment like rotors, LNB switches, etc.
The most common use would be to switch, for example, between two different satellites that are received by 2 different LNB's or dishes, and hook it up to one single reciever.


Why DiSEqC?


Older satellite recievers started to create their own little standard and solution for several switching purposes. This started to confuse customers (which works with what?) so it was time for a decent standard.
Some satelliet recievers use a 14/18 Volts currency to switch between the Horizontal and Vertical polarisation.

Another thing to switch, often done by using a 22Khz tone-burst, is switching satellites (2 LNB's either mounted on 1 or 2 dishes).
Now-a-days the upper frequency range (11,7 to 12,75 GHz) becomes more and more of interest for use in digital programs. The LNB's used for this purpose are universal LNB's (10,7-11,7 and 11,7-12,75 GHz) which use the 22kHz-Signal to switch between these two frequency ranges. This however is in conflict with the original use of the 22Khz Tone-Burst: siwtching between two satellites.
Using DiSEqC changes this for the better. In our digital world, we can send digital commands to the add-on equipment. DiSEqC is downwards compatible, so older equipment should work just fine with newer DiSEqC equipment. It's true that a DiSEqC 2.0 compatible receiver kan work just fine with a DiSEqC 1.0 LNB-switch.
The otherway around might or might not work, it all depends on the switch. Most of them do listen to DiSEqC 1.0 commands, some don't.
TIP: Make sure that you can return the switch if it's not working properly.
The concept of DiSEqC continues to use 14/18 Volts and 22Khz tone-burst concept. DiSEqC additionally uses digital commands to control equipment (naturally, both receiver and switch must be DiSEqC compatible).
DiSEqC is of use for both analog, digital and analog/digital systems.


DiSEqC variants


Mini-DiSEqC
Uses the 22Khz Tone-Burst (= Mini-DiSEqC), being able to switch between two individual universal LNB's (for both digital and analog satellite reception), where the switch always has only one of the two LNB's active. This switch is a specific DiSEqC compatible switch using both the 14/18 Volts cuurency and the 22 kHz Tone-Burst for control purposes.
DiSEqC 1.0
DiSEqC Version 1.0 allows you to connect up to 4 receivers to your receiver, where the receiver (master) controls the switch (slave) by sending digital commands for selecting the desired LNB.
These signals are used:
- low or high band frequency
- vertical or horizontal polarisation
- which LNB should be activated
DiSEqC 1.0 uses:
- reception of 1 satellite (using 1 LNB) - 14/18 Volt
- reception of 1 satellite for both digital and analog reception - 14/18 Volt
- reception of 2 satellites (using 2 LNB's) - 14/18 V + Tone-Burst
- reception of 4 satellites (using 4 LNB's) - 14/18 V + Tone-Burst + Loop-Through
Special LNB's allow you to use the Loop-Through signal, where the 2nd LNB's signal is being routed through the 1st LNB. This works with DiSEqc 1.0.
DiSEqc 1.2
Can additionally be used for automatically control of rotor-based dishes.
DiSEqC 2.0
DiSEqC 2.0 adds a return channel, used for getting information on the connected add-ons. It will inform the reciever, after sending a particular signal, about the amound and type of LNB's available and how they are interconnected.
Particular 2.0 applications (Next to the 1.0 applications):
- Reception of up to 4 sattelites
- Two way channel (info on what's connected to the receiver)
DiSEqC 2.1
Adds the ability to control up to 64 LNB's, I can't imagine what my house would look like with that many dishes, but hey,... you can if you want to (sent me a picture!).


Which DiSEqC version do I need?



When using only one dish, with 1 LNB for only one satellite: basically any equipment will do just fine.
If you want to receive 2 satellites, for example the Astra and the Hotbird (EutelSat), your reciever should at least be able to control one switch, using any DiSEqC version. Actually a Tone-Burst ability should be sufficient.
When using 3 or more dishes, you will definitly need at least DiSEqC 1.0 or higher (depending on what your setup looks like).
When using a rotor for your dish to change position, you should go for DiSQeC 1.2 or higher.
Note that almost ALL LNB switches support DiSEqC 2.0, but often they are able to work with lower versions aswell. At least that is what is said... only experimentation will show if it works, so make sure you can return the switch if it doesn't work.
Most LNB switches sold in Europe are inteded to work with the Astra and the Hotbird (Eutelsat). This implies they should work with the receivers for these satellites aswell. Most modern receivers support at least DiSEqC 1.0 anyway.
Отговори с цитат
Следните потребители БЛАГОДАРЯТ на ТИНТИН за този полезен пост :
netman (08-08-2009)
  #4  
Стар 09-07-2009
Аватара на hajduk
hajduk hajduk не е на линия
Форумец с мегер
 

Дата на присъединяване: Apr 2009
Местоположение: Варна
Мнения: 869
Благодари: 1,812
Получил благодарност:
345 пъти в 184 поста
Сваляния: 111
Ъплоуди: 4
По подразбиране

Цитирай:
Първоначално написано от Ooo_Pepi Вижте мненията
Много хубаво, ако някой се навие да го преведе ще бъде прекрасно. 10х
Кое точно не разбираш да ти го преведа - ако нищо не разбираш - и да ти го преведе някой, ще трябва и да ти го обясни ...
Отговори с цитат
  #5  
Стар 23-04-2011
Аватара на lordzerg
lordzerg lordzerg не е на линия
Zerg
 

Дата на присъединяване: Dec 2010
Мнения: 111
Благодари: 2
Получил благодарност:
3 пъти в 3 поста
Сваляния: 4
Ъплоуди: 0
По подразбиране

пробвах какви ли не начини и не мога да го направя нещо не е наред.

значи да обясня : преди няколко дена си сложих втора чиния без мотор към сегашната която е с мотор.
да кажем че моторизираната ми чиния е ЛНБ2 вързана на 2 порт на дисека
а ЛНБ1 е вързана на 1ви порт на дисек ключа и е статична без мотор.
сега настройките на дриима ми 500С .
да предположим че статичната ми антена е настроена за 39Е а моторизираната има настроики за 25.5Е True south и астра на 28.2 тия двете съм ги нагласил на ЛНБ-0 а 39Е ми е ЛНБ-1

настроиките на ЛНБ-0
diseqc 1.2 A/B Uncommited switch НЕ другите отметки не съм слагал също

ЛНБ-1 същите настроики но А/А и не става . също пробвах тая чиния безмотора да я пусна на дисек1.0 пак не става. пробвах и без параметри но пък с Uncommited 1 i 2

дайте малко ъкъл къде бъркам

Последно редактирано от lordzerg : 23-04-2011 на 18:20
Отговори с цитат
  #6  
Стар 23-04-2011
PhilipZ PhilipZ не е на линия
мега форумец
 

Дата на присъединяване: Jul 2008
Местоположение: София
Мнения: 527
Благодари: 115
Получил благодарност:
143 пъти в 104 поста
Сваляния: 188
Ъплоуди: 7
По подразбиране

Ще цитирам един колега който писа преди два дена за подобен проблем:
Цитирай:
Първоначално написано от Никки Вижте мненията
Въйко го е обяснявал 100 пъти. Мотор и дайсек се вързват по следния начин - приемник -> мотор -> дайсек -> конвертор. Вързваш го така и всичко е наред. Аз съм с 10торен ключ и досега по тази схема не съм имал никакви проблеми.
Освен това обикновен DiSEqC ключ се управлява като commited! Обърни местата на конверторите - моторизираната да иде на 1-ви вход, а стационарната на 2-ри. Ако още не ти е ясно питай какво точно. Също така пробвай за настройка и комбинацията B/A и B/B за конвертора на 2-ри вход (някой чипове в ключовете възприемат командите наопаки)

Последно редактирано от PhilipZ : 23-04-2011 на 19:55
Отговори с цитат
  #7  
Стар 23-04-2011
Аватара на lordzerg
lordzerg lordzerg не е на линия
Zerg
 

Дата на присъединяване: Dec 2010
Мнения: 111
Благодари: 2
Получил благодарност:
3 пъти в 3 поста
Сваляния: 4
Ъплоуди: 0
По подразбиране

значи това няма да стане сега да мине първо през мотора защото трябва да сменя бая кабели дисека ми е захванат за стената антената е на 3-4 метра

може да пробвам да разменя входовете на дисека
Отговори с цитат
  #8  
Стар 24-04-2011
PhilipZ PhilipZ не е на линия
мега форумец
 

Дата на присъединяване: Jul 2008
Местоположение: София
Мнения: 527
Благодари: 115
Получил благодарност:
143 пъти в 104 поста
Сваляния: 188
Ъплоуди: 7
По подразбиране

Цитирай:
Първоначално написано от lordzerg Вижте мненията
значи това няма да стане сега да мине първо през мотора защото трябва да сменя бая кабели дисека ми е захванат за стената антената е на 3-4 метра

може да пробвам да разменя входовете на дисека
Ако кабела първо ти минава през ключа и след това отива в мотора има вероятност мотора да не ти работи добре защото консумира относително голям ток и пада на напрежение в ключа ще е по-голям. Измисли начин да следваш предписанието на Въйко - работи 100%.
Отговори с цитат
Sponsored Links
VIVO Rent A Car  Вземи своят Vu+ сега!  SatPlus
Отговори

Съобщения от Devil M
VIVO Rent A Car  

Тагове
diseqc, works


Активни потребители разглеждащи тази тема в момента: 1 (0 членове и 1 гости)
 
Контрол над темата Търси в тази тема
Търси в тази тема:

Разширено търсене
Начин на разглеждане

Подобни теми
Тема Започнал темата Форум Отговори Последно мнение
DM500HD Display, YES IT WORKS dsc DREAMBOX 10 15-07-2010 09:55
DISEqC ключ mimetomm САТЕЛИТНИ АНТЕНИ 21 23-02-2010 01:48
DiseqC проблем. system САТЕЛИТНИ АНТЕНИ 8 07-12-2009 22:33
Настройка на DiSEqC 8x1 ? Трънката DREAMBOX 16 07-11-2009 04:53


Всички времена са във формат GMT +3. Часът е 16:24.


DTV-BG Powered by vBulletin Version 3.8.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.