Цитирай:
Първоначално написано от shemetcho
Отиди на Client -> Configuration, натисни бутончето Open и разгледай примерите и ще ти светне
|
N линията стана но къде се слага C линия това е конфига на фаусто
############################################################
# syntax for CCcam Client connection
# F: IP PORT WANTEMU USERNAME PASSWORD {CAID-4 byte len/PROVIDS-6 bytes len} [Server Version-Build]
# WANTEMU=0 Disable CCCam Emu on sharing
# WANTEMU=1 Enable CCCam Emu on sharing
# [Server Version-Build] optional but required for local home share, must be same as server
# By default: [2.1.1-2971] used over the net
# CCCam version Build
# 2.1.3 3165
# 2.1.2 3094
# 2.1.1 2971
# 2.0.11 2892
# 2.0.9 2816
# 2.0.8 2699
# example:
# F: 127.0.0.1 9000 1 dummy dummy [2.1.2-3094]
# or
# filtered on Caid/provids
# F: 127.0.0.1 9000 0 dummy dummy {0100/003315 003317} [2.1.2-3094]
#
#
# syntax for NEWCAMD Client connection
# N: IP PORT USERNAME PASSWORD KEY-14 bytes len
# example:
# N: 127.0.0.1 10000 dummy dummy 0102030405060708091011121314
#
#
# syntax for RADEGAST client connection
# R: IP PORT {CAID-4 byte len/PROVIDS-6 bytes len}
# example:
# R: 127.0.0.1 11000 {0100/003315}
#
#
# syntax for CAMD33 client connection
# K: IP PORT USERNAME PASSWORD KEY-16 bytes len {CAID-4 byte len/PROVIDS-6 bytes len}
# example:
# K: 127.0.0.1 12000 dummy dummy 0123456789ABCDEF0123456789ABCDEF {0100/003315}
#
#
# syntax for CAMD35 TCP client connection
# L: IP PORT USERNAME PASSWORD {CAID-4 byte len/PROVIDS-6 bytes len}
# example:
# L: 127.0.0.1 13000 dummy dummy {0100/003315}
#
#
# syntax for CAMD35 UDP client connection
# M: IP PORT USERNAME PASSWORD {CAID-4 byte len/PROVIDS-6 bytes len}
# example:
# M: 127.0.0.1 13000 dummy dummy {0100/003315}
#
#
# syntax for GBOX LISTENER client connection
# only 1 G line worked
# G: {CAID-4 byte len/PROVIDS-6 bytes len}
# example:
# G: {0100/003315}
#
#
# syntax for TWin Client Protocol
# T: COMPort,Baud,DataBits,StopBits,Parity
# COMPort: COM1 to COM255 -> where dongle connected
# Baud: 1 to 256000
# DataBits: 5 or 6 or 7 or 8
# StopBits: 1 or 2
# Parity: N (none) or E (even) or O (odd) or M (mark) or S (space)
# Example: T: COM2,115200,8,2,N
#
#
# syntax for Connection max delay
# (=max delai for connection response, if exceed connection will be considered like FAILED
# Connection: Value is in ms (1000 ms = 1 sec)
# default value is 5000 ms (=5 secs), if Connection not set on file
# example:
# Connection: 5000
#
#
# syntax for Client Max Timeout
# (=max delai for server response, if exceed server will be considered like down
# & FE will try to reconnect auto
# TimeOut: Value is in ms (1000 ms = 1 sec)
# default value is 3000 ms (=3 secs), if Timeout not set on file
# example:
# Timeout: 3000
#
#
# syntax for Ignore SID
# I: SID {CAID/PROVIDs} PORT
# example:
# I: 2009 {0100/003315} 10500
# I: 2010 {0100/003315 003317} 10500
# For Newcamd/CCCam use Port cause caid/prids read after login
#
#
# syntax for Irdeto/Betacrypt CHID filter
# enable ECM for CHID and provider concerned others exclude
# C: CHID {CAID/PROVIDs} PORT
# example:
# adressed to server on port 11100
# C: 0004 {0604/000000} 11100
# adressed to all servers
# C: 0004 {0604/000000}
# For Newcamd/CCCam use Port cause caid/prids read after login
#
#
# syntax for CCcam MAXID
# Max Same Card for ECM prid
# Fausto will Try MAXID Share for decoding ECM
# default set to 0 (=use all Caid/PrId found)
# MAXID: value
# example:
# MAXID: 4
#
#
# syntax for CCcam Ignore Node
# INODE: NodeID
# example:
# INODE: AABBCCDDEEFFGGHH
#
#
# syntax for CCcam Node Priority
# PNODE: NodeID
# example:
# PNODE: AABBCCDDEEFFGGHH
#
#
# Ignore Caid/PrIDs for CCCam Node
# If Node is not applied in the line,then in this case Caids/PrIds Ignore list will be apply for all nodes
# Usefull cause somes card on server can't decode channel (no rights)
# or
# if you got better response ( less latency ) from another CCCam server in Fausto Manager List
#
#Syntax
# ICPN: {Caid/Prids list} NodeId
# if NodeID Misssed caid/prids ignored for all nodes
# Example
# ICPN: {0500:020810/020820/020830/020840/020850/020860} AABBCCDDEEFFGGHH
# ICPN: {0100:00A821/00A825/00A829/00A82D} AABBCCDDEEFFGGHH
# ICPN: {0D22:000004/000008/00000C/000010} AABBCCDDEEFFGGHH
# ICPN: {1702:000000/000001/000002/000003} AABBCCDDEEFFGGHH
# ICPN: {0961:000000}
#
#
# syntax for ECMDEBUG
# possible value: ON or OFF by default is OFF
# ECMDEBUG: OFF
#
#
# syntax for EMMDEBUG
# possible value: ON or OFF by default is OFF
# ECMDEBUG: OFF
#
#
# syntax for AUTO RECONNECTION
# possible value: Enabled or Disabled by default is Disabled
# AUTO: Disabled
#
#
# syntax for LOG on FILE (worked in append mode)
# LOGFILE: Drive + File Path + File Name
# ECM log on file enabled ONLY if ECM DEBUG enabled (under this file or under Tab Manager)
# example:
# LOGFILE: C:\Program Files\Fausto\FaustoClients.log
#
#
############################################################
#
#
#
# NEWCAMD CLIENTS FOR TESTS
N: 127.0.0.1 10000 dummy dummy 0102030405060708091011121314
N: 127.0.0.1 10100 dummy dummy 0102030405060708091011121314
# RADEGAST CLIENTS FOR TESTS
R: 127.0.0.1 21400 {0100/000030}
R: 127.0.0.1 21600 {1801/002111}
# CAMD33 CLIENTS FOR TESTS
K: 127.0.0.1 24600 dummy dummy 0123456789ABCDEF0123456789ABCDEF {0100/000030}
K: 127.0.0.1 24800 dummy dummy 0123456789ABCDEF0123456789ABCDEF {1801/002111}
# CAMD35 TCP CLIENTS FOR TESTS
L: 127.0.0.1 41200 dummy dummy {0100/000030}
L: 127.0.0.1 41300 dummy dummy {1801/002111}
# CAMD35 UDP CLIENTS FOR TESTS
M: 127.0.0.1 45200 dummy dummy {0100/000030}
M: 127.0.0.1 45300 dummy dummy {1801/002111}
# GBOX (LISTENER) CLIENTS FOR TESTS
G: {0100/000030}
# Ignored SID
# sid 2141 = Rai Tre
#I: 20B4 {0100/003315} 21000
# CHID Filtered
# S1 on hotbird
# Only ECM for this chid will be accepted
#C: 0004 {0604/000000} 11100
# others settings here
ECMDEBUG: OFF
EMMDEBUG: OFF
AUTO: Enabled